sata interposer

The main types of hard disk interfaces currently available are IDE, SATA, SCSI, SAS, FC, and so on. The IDE is commonly known as the port, SATA is commonly known as the serial port, both of the hard disk is the PC and low-end server common hard disk. SCSI is the abbreviation for "Small computer system dedicated interface", which is the hard disk with this interface. SAS is the SCSI interface of the serial p

The use case is simple, I want to use both SSD disks and SATA disks within the same machine and ultimately create pools pointing to SSD or SATA disks. in order to achieve our goal, we need to modify the crush map. my example has 2 SATA disks and 2 SSD disks on each host and I have 3 hosts in total. To revoke strate, please refer to the following picture: I. Cr

How to change SATA mode to AHCI mode after computer installs SSD solid State drive 1, restart and press the shortcut key to enter the BIOS setup interface, and some laptops are by the side of the button to enter; 2, choose to enter the BIOS Setup; 3, switch to the configuration interface; 4, select the SATA control Mode; 5, select "AHCI"; 6,

SASAndSATAHard Disk differences As you know, like ata, SCSI is a parallel technology that can connect multiple devices through their respective data channels. Like ata, SCSI is also evolving towards Serial technology, which is SAS (Serial Attached SCSI ).In short, SAS is a new generation of SCSI, which includes some improvements, such as higher transmission speed, better scalability and reliability. Some people think that SAS is a technology that integrates the advantages of SCSI and Serial ATA.

SATA Hard Disk There are many advantages, but the installation operation System Reality Trouble Not only do you have to seize the opportunity to press the "F6" key to load the stat driver Program , You also need to create a floppy disk with a driver. What's terrible is that if the new machine is not configured with a soft drive, it will be very eye-catching ...... To create a WINXP installation disc containing the

??To SATA interface (according to the Linux kernel to check its order sda,sdb ...) As an example,1, the limit of the hard disk, the maximum can only set 4 partitions (primary partition + extended partition), the path such as the following,/dev/sda1/dev/sda2/dev/sda3/dev/sda42, operating system restrictions, the extended partition can only have up to 1, can be 3 (or below) primary partition + an extended partition,3, the extended partition uses the add

Now when you install Windows Server 2003 for your server, or when you install XP for a workstation that uses SATA raid, you need to load the associated driver from the floppy drive, but many machines do not have a floppy drive. For a server, you can install it using the boot CD from the server, but the first logical disk for the disk display will be partitioned when installed. In the past, most of the drivers for SCSI cards, RAID cards,

:39.56ms (99%) [50s] threads:16, tps:1024.20, reads/s: 14342.20, writes/s: 4098.50, Res Ponse time:38.07ms (99%) [60s] threads:16, tps:1034.90, reads/s: 14480.88, writes/s: 4136.40, Response time:37.70m S (99%) [70s] threads:16, tps:947.10, reads/s: 13266.32, writes/s: 3793.20, Response time:122.98ms (99%) [80s] Threads:16, tps:1006.20, reads/s: 14081.49, writes/s: 4020.40, Response time:77.28ms (99%) [90s] threads:16, TPS: 938.30, reads/s: 13133.50, writes/s: 3753.10, Response time:129.52m

Http://njdg.net/bbs? A = gzhnan Http://www.51cto.comAuthor: Nonferrous Metals · SATA hard disk BIOS settings: --> With the decrease in prices and the support of the corresponding motherboard, Sata hard disks have gradually become the mainstream. However, due to the impact of the chipset and operati

I. Question proposalThe current computer hardware is basically a SATA hard drive,The main board is mainly used to adapt to the SATA ahci mode.The original installation disk of the application's XP system has been directly set up and must be correctly installedYou need to set the bios, change the mode to the ATA mode, and wait for the system to installAfter installation, you must manually set the ahci driver

Before a lot of friends asked the SATA hard drive can use Ghost, in the use of ghost to the system to do backup, may have encountered this situation, With floppy disk or CD-ROM boot into the system, when the use of GHOST.EXE command System black screen, crashed. Is ghost not supported SATA devices? Can't we make a backup of the system after we use SATA drives? Th

One, BIOS setup section Because each motherboard's BIOS is not the same, but the principle is basically consistent, here only a few more typical BIOS settings, I believe that readers can refer to the actual situation of the motherboard BIOS to solve the problem. 1. The South Bridge is the ICH5 motherboard Let's take Asus ' p4c800 as an example, the motherboard chipset is I865PE, and the South Bridge is ich5/ich5r. After entering the BIOS, select the IDE Configuration Menu under Main, and unde