Learn about set security on linksys wireless router, we have the largest and most updated set security on linksys wireless router information on alibabacloud.com
1, run the command prompt as the administrator. Start → run, enter cmd.
2. At the command prompt, enter the command: netsh wlan set hostednetwork mode=allow ssid= The name of the wireless network you want key= the password you want to set.
3, then open the Network Sharing Center-Change adapter settings, you will find one more Microsoft Virtual WLAN Miniport Ada
tp-link Router WiFi wireless network setup method
Click on "Wireless Settings" and "Basic settings" to see the interface shown in step 2.
Enter your own name in the SSID, preferably in English so you can maintain good compatibility with more equipment. The name you enter here is the name you see when you use a mobile device such as a mobile phone, a
G1 Web certification, mainly for some enterprises and Internet cafes certification, need to give a specific device account password, so that a specific device users can access the Internet, the specific operation as shown in the following figure:
First Step : Connecting Lines
Step Two: Enter the Setup authentication interface
Third Step : Authentication Infrastructure Settings
Fourth Step : Add An authenticated user's account number and password
wireless network is just established virtual wireless card, you can see the following typesetting, Microsoftvirtual WIFI ... This row, I know.
4. Then set in the broadband connection, right-click, properties-Share, and then "Allow other network users to connect through this computer Internet connection" tick,
Then select the following "Home network Connection"
tp-link Hyfi Intelligent Wireless Router Setup first step, Hyfi router and extender registration
1, the Hyfi router and extender plug in the power outlet.
Plug the Hyfi router and extender into the socket
2, when the Hyfi router's LED is often bright, press th
"Win7 Set Wireless router method steps"
The router picks up the power cord and connects the WAN interface with the network cable
OK, enter the network name (set yourself), enter the pin on the back of the router-----complete
. Currently, a certain scale of networks use dynamic routing protocols, which are commonly used: RIP, VPN, OSPF, IS-IS, and BGP. When a vro with the same routing protocol and region identifier is added to the network, the route information table on the network is learned. However, this method may cause network topology information leakage. It may also disrupt the routing information table that works normally on the network by sending its own routing information table to the network. In severe ca
First step:
Connect a good line, an outside line inserts a WAN port and then uses a network cable to plug in one of the remaining 4 ports and connect to the computer (the IP of the NIC is set to get the method automatically or the IP set to 192.168.0.X (2-254) is not specifically understood). Then open IE, enter 192.168.0.1 in the address bar as shown
Step two: The following interface appears,
(with a light cat) to separate the light cat a network cable to connect the router's WAN port (blue logo), and then find a short network cable, a computer, a router 1/2/3 arbitrary interface (yellow), wiring mode as shown below:
Note: When powered on, the router is working normally with the SYS LEDs flashing, WAN LEDs illuminated steady or blinking, and the 1/2/3 port LEDs attached
2, (a light cat) to the light cat out of a network cable to connect the router's WAN (blue logo), and then find a short network cable, a computer, a router 1/2/3 arbitrary interface (yellow), wiring mode as shown below:
Note: when powered on, the router is working normally with the SYS LEDs flashing, WAN LEDs illuminated steady or blinking, and the 1/2/3 port LEDs attached to the computer are illuminated s
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.