sfp switch 8 port

]rulepermitipsource10.10.1.10destinationany [SwitchA-acl-link-3000] rulepermitipsourceanydestination10.10.1.10 3. Will pass through the port G1/0/1, matches the ACL rule the message to mirror to the monitoring port [SWITCHA]INTERFACEGIGABITETHERNET1/0/1 [SWITCHA-GIGABITETHERNET1/0/1] Mirrored-toinboundip-group3000monitor-interface [SWITCHA-GIGABITETHERNET1/0/1] Mirrored-tooutboundip-group3000monitor-inter

allows packets sent by default VLAN without tags. 1.4 Fabric port Mode The Fabric port is the port between units in IRF. It is only used for interconnection between units and cannot connect users. 2 Application of Hybrid port Mode By introducing the various link port modes

the direction of message flow limit to the speed limit to 3Mbps [Switcha-ethernet0/1]line-rate Inbound 1 The total rate at which a message is sent or received by the port is indicated here at 8 levels, with a value range of 1~8, which means that when the port is working at a 10M rate, 1~

) #Exit//Exit VLAN configuration state sw02(config) # interface Ethernet G1//Enter port configuration status sw02(config-if) #switchport Access VLAN 100//Configuring VLANSW02 for Ports(config-if)Exit//exit port configuration status sw02(config)Exit//exit configuration State sw02#show VLAN//Show VLAN configuration VLAN Name PortsTypeAuthorization---------------------------------------------------------------

Huawei switch Port monitoring), and the Port connecting to the listening device is called the "analysis Port" Analyzer Port ). Run the following command to configure a port listener for a Huawei switch:Feature rovingAnalysis add,

I. Port Mirroring concept: Port Mirror is used for network performance monitoring. It can be understood as follows: Establish an image relationship between port A and port B. In this way, data transmitted through port A will be copied to

Session 1 Port SecurityThe MAC address in the network is the constant physical address in the device, the control of the MAC address access control the switch port access, so port security is also the security of the Mac. In the switch, the cam (content addressable memory, t

In the tree menu on the left of the switch management interface, select switch (switch) >>> Ports (port) >>> "portmirroring" (port mirroring), and the right opens "portmirroring" (Port Mirroring) page. The parameters in this page

range is 1~4094. When you configure the watch port, if you do not specify a VLAN, the type of the observed port is local mirroring, and if you specify a VLAN, the type of the watch port is the remote mirror. 2. Configure the Mirror Port#将ETHERNET0/0/1----ETHERNET0/0/10 interface is configured as a mirrored

置SNMP协议的读团体字符, must be consistent with the settings on the switch.⑥units #设置端口流量的单位.⑦use Custom Multiplier # tick, and set the value to 8, if not set, units Unit is bps.⑧update interval #根据服务器的性能和监控的设备数量来设置, the default is also available.650) this.width=650; "title=" 8 "style=" border-top:0px;border-right:0px;background-image:none;border-bottom:0px; padding-top:0

To configure a vswitch port image, experts can understand the following knowledge about the vswitch port image configuration. You only need to complete the vswitch port image configuration in a few minutes. The local connection is also mentioned in this article. Vswitch images such as 3026]Vswitches such as S2008/S2016/S2026/S2403H/S3026 support

Huawei switch Port isolation, the implementation of the switch port is not interoperable, directly under each interface configuration port-isolate enable command. However, the Port-isolate command cannot be configured on an Allied