Alibabacloud.com offers a wide variety of articles about snapdragon development board, easily find your snapdragon development board information here online.
[Reprinted] The 4412 Development Board, PC, and ubuntu are connected through a network cable, and the 4412 ubuntu
Today, we can see that the Development Board uses TFTP to download programs directly from ubuntu without having to download them through the burning file system all the time. I tried it and the virtual mach
-write files . SofClick start to start the write program to the FPGA chip, and there will be a progress bar display, when the 100% is reached, that is, the success of the write, the Development Board on the corresponding LED Light is lit (this program is to write the program is downloaded into the SRAM , the power-down program will disappear, but after the completion of the burn, the circuit
This article explains how to debug our applications with the NFS network file system, where we use the Linux qt system asCases.When we debug the application on the qt system, we first build the executable binaries on the virtual machine Ubuntu by cross-compiling,Then copy the generated binaries to the file system, then regenerate the system.imgwith the command, then burn the system.img toDevelopment Board, and then launch the
In the previous article http://www.cnblogs.com/linzizhang/p/4817336.html introduced the first part of the system software on the Development Board--bootloader the compilation method.Background: After the bootloader is burned into the NAND flash of the Development Board, the Develop
Today, we got a Development Board, bv561evb, from Hefei Youshi technology. It consists of a basic board and a power board. It is very small and exquisite, and it looks like 10 cm x 7cm. Connect the 12 V power cord, connect to the serial port, open the Super Terminal, configure it to 115200-n-1, then connect the network
Address: http://blog.csdn.net/ipromiseu/article/details/5154004
Detailed solution for 3G cards on the Development Board (applicable to most 3g cards)
Anson Luo/gray Luo (Luo Guohui)
I. Environment
1.Development Board kernel: Linux kernel 2.6.14
2.3G card: Huawei e1750
2. Download related tools and library files
1. usb
Porting linux2.6.24 to the FS2410 Development Board is a preliminary success-Linux general technology-Linux programming and kernel information. The following is a detailed description. It is not accurate because the Linux kernel 2.6.24 has included the s3c2410 kernel. During the transplantation, you only need to make a few minor changes and pay attention to them.
I. Preface
Kernel used: linux2.6.24, http:/
1. Install serial debugging tool: Minicom, 1th step: Use insmod | grep usbserial command to detect whether the current system supports USB to serial port; Step 2nd: Install minicom using the Apt-get installation minicom command 3rd Step: Configure minicom with the Minicom–s command, step 4th: Test minicom with the minicom command 2. Burn Write Android system: (1) Use Eboot erase Nandflash method: 1th Step: Prepare work, use serial line or USB to serial cable to connect
1, Guangzhou chuang long tms320c6748 DSP Development Board free trial, the history of the most abundant C6000 DSP Development Board, not to be missed. Application Link: http://bbs.elecfans.com/try_Tronlong.html#trialimgApplication Period: Year 9 month Application Model: TL6748-EASYEVM, market price 1450 Yuan Number
After two days, it almost crashes. Finally.
The Development Board is directly connected to the PC network cable (note that it is not a common network cable, but a specific network cable ).
PC configuration: You need to set an IP address for local connection, which is in the same network segment as the IP address of the Development
to use, provided that you can get more than one address. It is not suitable for anyone who wants to conduct various network experiments, because you cannot control the network of the virtual machine and it goes out directly. The schematic diagram is as follows:
2: After installing VMware and Red Hat (remember to install the NFS installation package), configure the Linux network. Because the IP address of my Development
Because the ARM architecture Development Board can be based on the X86 architecture of the PC on the CPU instruction and the binary is different, and if the Linux driver needs to access the hardware, these hardware is difficult to simulate on the PC, so we need to debug and test on the Development Board with these hard
Configuration of tftp server in ubuntu 10.04 and use of tftp commands on the Development Board tftp server in ubuntu 10.04: Step 4: install the software required for tftp. First, install tftp-hpa and tftpd-hpa. The former is the client and the latter is the service program. Enter sudo apt-get install tftp-hpa tftpd-hpa on the terminal, install tftp-hpa and tftpd-hpa. Then you need to install xinetd, enter s
The eighth chapter introduces the experiment: Buzzer driver, let the development board make sound.This paper introduces the principle of buzzer and realizes a complete buzzer driver, which can control the opening and closing of buzzer.The buzzer is also called PWM pulse width modulation, the basic principle is to control the buzzer by the pulse to open and stop. A buzzer is a hardware device on a
How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet)
How do I practice writing drivers and developing BSP after I buy a development board? (Author: wogoyixikexie @ gliet)
---------- A newcomer asked questions at the csdn Forum
Recently I want to buy a 244
The 5th chapter: Build the test environment of s3c6410 Development BoardThis chapter mainly introduces the Android system installed on the OK6410 Development Board developed on the basis of Samsung's launch of the s3c6410 Development Board.Install serial debugging tool: Minicom1th Step: Detect whether the current syste
a simple drawing board development reprint please indicate source:http://blog.csdn.net/u012637501
(
embedded _ small J Sky )
first, drawing board principle1. Linear effectThe drawing board can appear on the surface of the user on the touch screen freely draw arbitrary graphics, but i
Statement: This article is original works, copyright belongs to the author of this blog, If You Need To reprint, please indicate the source of http://www.cnblogs.com/kingst/
In this chapter, we will briefly study the development process of the uC/OS system based on niosii. There are three tasks in the experiment: the first task is used to drive the DS1302 real-time clock, the second task is used to flash the LED lamp, and the third task is used to di
This article goes from WebEx to:http://www.topeetboard.comVideo explanation Address:http://v.youku.com/v_show/id_XOTI4Njc0NDIw.htmlKnowledge system of embedded technology: Learning steps for the iTOP-4412 Development Board and accompanying tutorialsEmbedded knowledge of a wide range of beginners difficult to get startedThis section describes the embedded technology learning steps for beginnersTry to play th
For Rongping 4412 Development Board use of related issues, for reference only.Note: RP4412 Development Board Upgrade burn write to inand boot must press the power button about 5S.Q: With the Rong product Samsung Exynos4412 Development Bo
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.