socket error errno 98 address in use

If the address bound to the socket in python is in use, errors may occur, In Linux: "Socket. Error: [errno 98] address already in

The following error occurs when you start PHP today:Service PHP-FPM startError:Starting PHP-FPM [09-aug-2014 00:45:40] error: Unable to bind listening socket for address '2017. 0.0.1: 661': AddressAlready in use (98)[00:45:40 aug-

again, the sender assumes that the other party has received the ACK reply normally, then it will normally close the connection! Second, the solution If the address of the socket binding in Python is in use, an error often occurs. Under Linux:Copy the Code code as follows: The "Socket.error: [

First, the reason analysis Today is writing a python and HTML5 Websocket instance, the end run rerun script always prompt the address already exists and is used! Query the relevant documents only know in the socket programming, when the client sends a message to the server side, after the connection is closed, if you run the server side program immediately, will prompt this

Tags: MONGO alt class listening port startup Roc PNG Technology shareError message: Listen (): Bind () failed errno:48 Address already in use for socket:0.0.0.0:27017 Port 27017 is already occupied Complete error information 2016-10-24t23:46:56.314+0800 E NETWORK [Initandlis

Install Nginx on ubuntu10.04 today, try to start nginx after installation completes, use the command: The code is as follows Copy Code Sudo/etc/init.d/nginx start The result is that it won't start, and the following error prompts hankcs@ubuntu:~$ Sudo/etc/init.d/nginx Start[sudo] password for HANKCS:* Starting Nginx nginx nginx: [Emerg] Bind () to [::]:80 failed (

Nginx [Emerg]: Bind () to 0.0.0.0:80 failed (98:address already on use)This error occurs when the configuration of Nginx is modified, the table name 80 port is occupied by the programList all ports:Netstat–ntlpThe discovery port is occupied by the nginx itself, so the program that takes up 80 ports is closedsudo fuser-

[Emerg]: bind () to 0.0.0.0: 80 failed (98: Address already in use) Error cause, emergbindNginx restart error: [emerg]: bind () to 0.0.0.0: 80 failed (98: Address already in

Nginx Restart Error: [Emerg]: Bind () to 0.0.0.0:80 failed (98:address already on use) Reason: This is the Nginx reboot often encountered, this is the Nginx repeated reboot caused themselves to occupy the port. (It may be that you set up the boot automatically, or start it repeatedly) Workaround: killall-9 nginx to kil

When I use service httpd restart, the server prompts: Starting httpd: (98) address already in use: make_sock: cocould not bind to address [:]: 80 (98) address already in

#/usr/local/apache2/bin/apachectl Start starting httpd: (98) address Alreadyinuse:make_sock:couldnot bind toaddress[::]:80 (98) address alreadyinuse:make_sock:couldnot Bind Toaddress0.0.0.0:80 No listening sockets available, shutting down unable to open logs [FAILED] 1.netstat-lnp|grep 80TCP 0 0 192.168.

In order to practiced hand, use the crawler to climb a "you know" bed, using the Urlretrieve function, not only slow, but also always error, not open timeout is the above mentioned socket error.Find many ways on the internet such as adding headers in the request, calling Urllib2. Request.urlopen (). The call to close () after read () has not worked.Because do not

After installing Apache in Linux, start the prompt (98) Address already in use: make_sock: cocould not bind to address [::]: 80, stillcouldnotbind I tested it in Ubuntu. The operations are the same for other system references. When you see this prompt, you should think of port occupation. Let's first netstat-lnp

#/etc/init.d/httpd StartStarting httpd: (98) address already in use:make_sock:could not bind to Address [::]:80(98) Address already in use:make_sock:could don't bind to address 0.0.0.0:80No listening sockets available, shutting do

fragments, the sender assumes that the other party has received the ACK reply normally, at this time it will normally close the connection! Ii. Solutions If a socket-bound address in Python is in use, an error often occurs. Under Linux: Copy Code code as follows: "Socket.error: [

UDP socket:read error Bad addressthe UDP server is being written. This error occurred while calling the socket read. By looking at errno.h to see the corresponding error numberEfault: Bad address (posix.1), see on the StackOverflow this explanation is good:

Writing a program in Python is really simple, and when we develop a feature, especially a Python program with a form, you need to turn the Python program into a double-click EXE program. We need a third-party module Py2exe, which is the module that turns the PY into EXE. Just py2exe How to install, I do not elaborate here, directly to the official web download corresponding to the Py2exe version of Python, and then a fool-type installation, and installed after the Py2exe module is automatically

Today, when you use _trename for file renaming, consider the possibility of renaming failures, and you need to log the errors corresponding to the error. From MSDN, the function fails to return a non-0, and the corresponding error code may be known through the errno macro. In order to locate the convenience of the prob

When developing debugging, the running ASPX page has the following problems:asp.net Development Server failed to start listening on port 2083.Error message:Typically, each socket address (Protocol/network address/port) is allowed to be used only once.After the study found that the original:All unmanaged resource progra

Article reproduced from: http://www.isongzi.com/2009/03/26/socket-bad-address/ I don't understand why I have bad address errors when I read the socket buffer. The send-side write return value is normal, and the receiving end read returns 0 and prints a bad address