Reason Analysis:
1, the system service problem;
2, the computer sound setting is not correct;
3, the sound card driver problem
Solution steps:
1, first open the Control Panel, and then click on the panel "Hardware and sound-Audio management device" option;
2, and then double-click the microphone to open the microphone properties interface, switch to the Level tab, and then adjust the
Speakers usually use when everything is normal, but after inserting the microphone, the speaker will immediately generate noise.
Microphone and sound card connector line does not use shielding line or shielding line grounding, external high-frequency interference signals by the microphone input string will cause noise. If you unplug the
Note: The purpose of this article is mainly for the laptop headphone jack No response problem, that is, the headset inserted but the computer sound still through the speaker.
First, open the Control Panel, the sound to see if the local sound card driver is Conexant Smartaudio HD series, if you continue to look down;
Second, in the headset itself is not defective, sound card driver normal and not mute, if the headset inserted or control speaker speakers, it is necessary to use the following met
Win7 Microphone Listening is a function in the system microphone management, microphone listening is a microphone with the use of an audio playback function, many Win7 users do not know what the role of this function is so small series for everyone to bring the Win7 system under the
In the network chat system, it is one of the most basic modules to collect the sound of the microphone and play it out. In this article, we describe how to implement this basic module quickly.I. Basic knowledgeThere are several professional terms related to sound capture and playback that must be understood first, otherwise, the subsequent introductions will not be expanded. Voice acquisition refers to the acquisition of audio data from the
"balance" will pop up a balance dialog box, where we can adjust the left and right sound,"forward" and "backward" as shown in the following figure.
8. Then we're going to "microphone volume" We click on the recording in the sound panel and then we right click on the microphone (you need to access the microphone before you can adjust the
recording microphone device Mxl.dwcomponenttype = Mixerline_ Componenttype_dst_wavein; Gets the number of connections in the recording bus Mixergetlineinfo ((hmixerobj) hmixer, AMP;MXL, Mixer_objectf_hmixer | Mixer_getlineinfof_componenttype); Save the number of connections DWORD dwconnections = mxl.cconnections; Ready to get the microphone device ID DWORD Dwlineid = 0; Esult Mr = Mixergetlineinfo (hmixero
1, we can start from the computer with the device to restore the microphone equipment, click Start, enter the Control Panel, click "Hardware and Sound", find "management of audio equipment", click on the recording, find the microphone, as shown in the picture:
2, find the microphone click Properties, Device methods: Enable the device. It's simple! Figure:
1. In Windows 10, we click on the "Start" menu in the lower left corner, and then click on it after entering.
2. Then find the following "Settings" option, click to enter;
3. Then locate the "privacy" in the following "Settings" and click on it to open the details below;
4. So we click on "Privacy"-"microphone" then you will see the microphone is turned on, this default is open;
Import flash. Events. activityevent;Import flash. Media. Microphone;VaR devicearray: array = microphone. names;// Name of all available sound Capture DevicesVaR mic: microphone = microphone. getmicrophone ();// Obtain the index value of the current microphoneMic. Gain = 60;// Micro
Why is there a small replay of sound after a microphone recording?
1, the microphone is set to a lower volume.
2, installed an incorrect sound card driver.
Here is a detailed list of the corresponding solutions.
Workaround:
First, if it is a Windows XP system.
1 Click Start, program, Settings, Control Panel, double-click to open Sound, voice, and audio devices, and click the Options menu to open prop
When we used the Windows XP system, did we find that some computers echo the microphone? That is because we have opened the "microphone" in the sound settings under the option, the previous I often used this function as a judge is good is a bad way, I do not know whether we have tried.
But in the Win7 version, if we want to use this method to determine the microphone
How to convert a single-ended microphone into a differential microphone input? Thank you!
Which one do you want?
The mic end of the false difference is grounded at the other end, and the signal at both ends of the resistance is collected to form the false difference.
The real difference is that the two ends of the MIC pull a bias and then input to the differential input.
Unfortunately, I won't draw
1, install the system, remember to update the system drive, do not use the system with its own drive.
The system automatic sound card drive, perhaps you listen to the song, the system brings the sound recording function these all can use, but the design to some software may not support. So download the system, or to update the driver.
2, where the microphone can be set in Win7
In the Control Panel, click on the sound, then switch to the recordin
This tutorial mainly uses Photoshop to draw a microphone for stereo effects. I like this tutorial very much. Especially the metal effect of the microphone head. Very creative, with unique ideas. let's take a look at it first.
Draw microphone Lesson 1: plug
Lesson 2: MicrophoneStep 1: Create a microphone head1
Silverlight4beta brings a much-anticipated new feature: Support for cameras/microphones.
This article will demonstrate this new feature through an instance of camera operations. Our instance mainly implements the following functions:
Display Device Name
Start/stop video capture
Real-time image capturing
The microphone usage is similar to that of the camera and cannot be intuitively displayed.
Old Rules: Let's create a simple UI first. The XAML
Step one, first check the bottom right corner of your taskbar to find the speaker icon, and then right-click the icon, and then pop up a dialog box, select the "Recording device" on the window, as shown in the picture:
After selecting a good recording device, a sound Properties window will pop up, select the default device microphone on the window, and then right-click the option to pop up the dialog box and select the "Disable" option. A
C # microphone acquisition and Playback,
In the online chat system, collecting and playing the microphone sound is one of the most basic modules. This article describes how to quickly implement this basic module.I. Basic Knowledge
Several terms related to sound collection and playback must be understood first. Otherwise, the subsequent sections will not be available. Voice acquisition refers to the acquisit
What if the microphone of the YY Live assistant has no sound?1) make sure that your microphone is recognized by the computer. If only the "main sound capture driver" is selected for the microphone, it indicates that your microphone is not recognized.2) try to disable the live video assistant and re-open it.3)
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.