configuration, which has been written for a long time,2950 The basic configuration of the switch, currently we are commonly used to configure the VLAN, the other is easy to manage, configure the IP address and allow Telnet login. Like spanning tree and VTP, the general small enterprises or systems are not configured, do not explain.1 Basic Concepts1.1 Classifica
EtherChannel sum view "Port aggregation/link Bundle #sh int port-channel View" Port aggregation/link Bundle #show spanning-tree view spanning tree status#show access-list View rule status#show History View Historical input commands#show errdisable Recovery see which protections can be automatically recovered after a timeout#showerrdisable Detect ? View err-disabled reason for the state6. Configure the IP of the VLANS (config) #int VLAN 6S (Config-vla
The implementation of the multi-port Cisco switch module is a common problem. How to configure the Cisco switch module, any problems related to ports will be fully resolved in this article.
Cisco
security, management, and integrated Cisco IOS features
CISCO switch 2950 has several unusual features to improve network performance, manageability, and security. Network administrators can configure up to 64 virtual VLAN VLANs for each vswitch) to achieve higher data security and enhanced LAN performance. This ensur
found again. This time it is smaller. It is disconnected when it is uploaded to 16 Mb. The system still prompts timeout and write error.
After careful analysis, we finally found the key to the Cisco switch failure. Two transmissions, 32 MB at a time and 16 MB at a time. Even the number of bytes is not bad, it is certainly not a problem with the transmission line. After checking the information, TFTP (Trivi
be built, while CD signals often exist. In addition, if one end of the X.25 line fails, and the other end of the X.25 line is often normal, so if the normal end of the router has data transmitted to the abnormal end, the router considers the X.25 line to work normally. Therefore, there is no backup line at all. Steps for displaying backup Method Configuration 1. Correctly configure trunk lines for normal
The article I want to share and configure VLAN on Linux through Cisco Catalyst Switch.Requirements:1. Linux installed on a PC with one or more NICs (Network Interface Card). I Use the Centos 5.4 using 2.6.18-164.11.1.EL5PAE kernel. It should is applicable on other Linux distros such as Slackware, Ubuntu, Fedora, Debian, etc.2. Cisco Catalyst
.
Breakthrough Cisco switch cluster technology
You can use the new Cisco switch cluster technology to achieve scalability and manageability beyond the stack. You can configure any Catalyst 3500 XL series or 2900 XL series standard or enterprise
a switch, we will inevitably enter an incorrect command, for example, if we type one more letter or one less letter, I thought the switch would prompt this command error, but a strange thing happened at this time. The system didn't prompt us for a command error, but made a connection to it (that is, the command was executed the same ), 3550 # beijing.
That is to say, the
, and multimedia support for enterprise intranets.
Introduction to the Catalyst5000 Series
Cisco's ipvst5000 series Cisco LAN switches, in addition to the Catalyst 5000, also include four models: Catalyst 5002, Catalyst 5500, Catalyst 5505, and Catalyst 5509, all of which are Catalyst 5000 enhanced. The old device used in this project is a Catalyst 5509 switch. Taking the common Catalyst 5509 as an example,
mean? When debugging a switch, we will inevitably enter an incorrect command, for example, if we type one more letter or one less letter, I thought the switch would prompt this command error, but a strange thing happened at this time. The system didn't prompt us for a command error, but made a connection to it (that is, the command was executed the same ), 3550 # beijing.
That is to say, the
current configuration information (Information in RAM) 51cto # show startup-config \ view the information of the saved disk (Information in NVRAM) 51cto # show ip route \ view route table information 51cto # show cdp neighbors \ check which cisco devices are connected to this vro 51cto # erase startup-config \ recover the vro to the factory configure 51cto # reload \ restart vro password recovery 1 start u
password to enter the privileged mode, and the original configuration content is retained.Operation steps: 1. Prepare the console cable and connect the Super Terminal. 2. Restart the switch (because 2950 does not have a power switch, you can directly unplug the power cord and connect it back.) 3. Press the MODE key at the start to enter the
A router is a commonly used network device. How should we configure VOIP implementation? What are the specific operation steps? The following article will give you a detailed introduction.
Using the Cisco router configuration can easily implement VoIP, So I studied the statements related to the Cisco router configurati
In the complex network environment today, the switch has become indispensable, so the switch manufacturers also develop quickly, here to take Cisco to give us a simple exchange! Cisco: Cisco; A simple introduction: Cisco is the wo
Cisco switch iOS upgrade, actually quite simple, but need to note is, can not let the switch flash storage is empty, must have an iOS in, or no iOS in Flash, waiting to upload iOS with Xmodem, so your time can be a lot of waste ah. Because the Rommon mode is not available for the Cisco Catalyst 2950, 2960, 3550
Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password protection.Switch>enable #进入特权模式
CISCO mds FC optical fiber switch configuration reference(1) There are several concepts that must be clarified (different from brocade ):(1) brocade divides zones directly. While mds divides zones under vsan, mds can divide several vsan first, and each vsan includes several zones.(2) brocase: the default port is open, while the default port of mds is closed.(3) mds has a Default zone: "The Default Zone ". i
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.