steps to configure cisco switch

Cisco L3 switch Policy Routing for network access and Traffic DistributionI. Description of the solution environment 1. There are two groups of Group1 and Group2 in the environment, respectively, to access the Internet from two different network outlets. 2. The core network is a Cisco 3560G layer-3 Switch with four VLA

A Cisco 4506 switch in the user's actual environment could not log on, and the system could only be cracked because the maintenance staff did not remember the modified password.Environment:Cisco Catalyst 4506E switch, engine for WS-X45-SUP8-E, system version is cat4500es8-universal-mCrack steps:To restart the switch, p

This article describes how to configure a vswitch for a CISCO 3550 router and how to configure access control for a MAC address. In network management, users often encounter this situation: some users violate management regulations and modify their own IP addresses without permission to access restricted resources. Such behavior not only undermines information se

Cisco 3750 switch stack configuration points 3750 stack is a real stack, the Catalyst 3550 series uses StackWise technology, it is an innovative stack architecture, A 32 Gbps stack interconnection is provided to connect up to nine switches and integrate them into a unified, logical, and optimized device for convergence, in this way, customers can deploy voice, video, and data applications with greater confi

=" Wkiom1soqq7ck2jtaahgkzym5xw472.jpg "/>(This picture is borrowed from others)Global Configuration Mode:1: enter this mode first. 2: port configuration such as:switch# configureterminalSwitch (config) #interface fastethernet 0/3Switch (config-if) #speed10// Configure Port Rate 10M default AutoSwitch (config-if) #duplexhalf//full Full Duplex Half Half Duplex AutoSwitch (config-if) #noshutdown// Open PortSwitch IP Configuration: The

Enable SNMP on the switch and configure the community name (Swap changer IP192.168.5.209)Switch (config) #snmp-server Community public roSwitch (config) #snmp-server Community public RW 2. Get the index information for the switch by entering the following command on the Nagios server[Email protected] ~]#/usr/local

Cisco Router Cisco2620 (config) # enable secret 123123: Set the privileged mode password to 123123 Cisco2620 (config) # line console 0: Enter the Console port configuration mode Cisco2620 (config-line) # password 123123: Set the Console port password to 123123 Cisco2620 (config-line) # login: Make the console port configuration take effect Cisco2620 (config-line) # line vty 0 5: Switch to remote logon Port

Tags: instance blank color 5.0 Ted Add dot1q message htmlTest topologyEnvironment: DHCP server and client are in different network segmentsConfiguration of DHCP serverNo IP routing IP dhcp pool vlan27 172.28.27.0 255.255.255.0 172.28.27.254 172.28.28.15 172.28.28.16 172.28.28.254 configuration of the L3-switchinterface Vlan27 IP DHCP relay information trusted172.28.27.254 255.255.255.0 IP helper-address 172.28.28.253 Access Switch configurati

Cisco switch QoS Speed limit configuration steps:1. Enable Global QoS2. Set the ACL matching traffic3. Set a class-map to match the ACL set in the second step4, set a Policy-map match Class-map, and then define a series of policies here, limit the bandwidth bitwise (BIT) for the calculation, burst in bytes (byte) calculation5, apply the POLICY-MAP to the correspo

Cisco switch Basic configuration: Console Port connectionUser mode hostname#;Privileged mode hostname (config) #;Global configuration mode hostname (CONFIG-IF) #;Switch Password settings:switchgt;enable; Enter privileged modeSwitch#config terminal; Go to global configuration modeSwitch (config) #hostname Csico; Set the host name of the switchSwitch (config) #enab

Cisco switches enable port speed limiting As shown in, Node switch 3550 is placed in an office room. The networks of all office companies are from this place. How does the operator configure network bandwidth settings for each company on this device? Let's take the IT Training Center of XX foreign companies as an example. The IT Training Center of XX foreign co

[Cisco] DHCP relay, layer-3 Switch VLAN Routing PracticeThe experiment topology uses the GNS3 0.8.6 simulator to build a DHCP server using Red Hat 6.5. The experiment requires configuring a layer-3 Switch VLAN routing so that VLAN10 and VLAN20 members can access each other. Performs DHCP relay for layer-3 switches so that VLAN10 and VLAN20 members can obtain IP a

Tags: process RAC ready alt Exchange Mutual picture Bubuko TFTP serviceWe will back up the configuration file and system image of the switch or router directly to the TFTP server, so we need to prepare a TFTP server1 We need to give the server an IP address, configure an IP address for the router's F0/1 port, and the router and the server can ping each other2. Configure