-Privacyname=Ens33uuid=b961637c-a4c0-4913-a161-81dfb4e21d49device=Ens33onboot=Yes #开机起来IPADDR=192.168.38.138 #ip地址Netmast=255.255.255.0 #子网掩码GATEWAY=192.168.38.2 #网关DNS1=119.29.29.29 #dsn The network service needs to be restarted after the configuration is complete:Systemctl Restart Network.serviceYou can then ping some of the popular sites:This means that it has been configured.My machine i
Basic Network ConfigurationTo connect a Linux host to a network, you need to configure network-related settingsGenerally include the following:Host NameIp/netmaskRouting: Default gatewayDNS ServerPrimary DNS ServerSecondary DNS serverThird-party DNS serversTo modify the NIC naming example:1. Check the driver of the
Linux operation and Maintenance Phase III (i) network configuration and remote managementFirst, network configuration1,#hostname (host name View#hostname FQDN (temporarily modifying host name#vi/etc/sysconfig/networkNetworking=yes ( host name configuration with IPV4Hostname=
One, Linux file Rights ManagementTo view a file's permissions command: Ls-lThere are 4 types of Linux file permissions: Read (r), write (W), execute (x), and no permission (-)Typically 10 characters to represent their permissions, grouped by (1-3-3-3)1 position means file type "-" for file, "D" for Directory2-4-bit representation of user rights (U)5-7-bit representation of group permissions (g)8-10 indicate
Redhat6.5 Virtual machine configuration nic1. Turn on the virtual machineRight-click and select "Open in Terminal"The following interface appearsThere are no C-drives, D-drives, e-disks in the Linux system. He was made up of documents,To connect an IP address that requires a virtual machine, you need to configure the virtual machine's IP address. First find out where you can configure IP. In a
all UNIX platforms-including HP-UX, Linux, AIX, Solaris, Digital UNIX, Irix, and other platforms-can run SSH.Normal SSH login need to enter the host password each time, in order to facilitate frequent landing, you can generate a key for the client machine and server to avoid the secret loginFour. SCP Transfer fileFive. Modify the SSH service default port and verify AccessResources1. Http://baike.baidu.com/link?url=Q97HqQhV4pt8GOrSnik87_-SYTlkE-ULnFz5
(4) Play with me Linux Network Services: DHCP service configuration-based relay proxy, linuxdhcp
Following the successful configuration of the DHCP server in Part 3, let's configure a relay proxy server.
Our Virtual Machine Structure
For details, refer:
(1) Play with me the Linux
The Linux operating system often applies the server, the network function is powerful.Linux Network Properties Configuration: ip/subnet mask, routing, Gateway, hostname,DNS server Configure IP:User space tool:ifconfig IPNetwork Device service configuration file:/etc/syscon
Today, we finally completed the Linux network configuration installed in VMware more than 10 days ago.When I was just using a virtual machine, I was fascinated by its magical virtual functions, because I always wanted to install linux on my computer, but because it is not compatible with windows, we are afraid that the
Vmwarevirtual machine linux network configuration-general Linux technology-Linux technology and application information, the following is a detailed description. Some time ago, I re-installed the system and had to reconfigure the vmware
domain name format is: Host name. Level three domain name. Level Two domain name--in fact, the IP network does not recognize the domain name, the IP network only recognizes the IP address, when the user enters the IP address directly, the router will directly send the request to the target host, but if the user enters the domain name, then the user's primary opportunity to first access the DNS server, The
mask)
GATEWAY = (Default GATEWAY)
ONBOOT = {yes | no} whether to start after adjustment
USERCTL = {yes | no} whether to allow common users to set the NIC (usually no)
PEERDNS = {yes | no} is used when the boot protocol is dhcp or bootp. If it is set to no
The dhcp Service or bootp service cannot change the host's dns configuration.
(Bootp is the predecessor of dhcp, but it does not have the lease function)
Disable an ifdown Device
Ifup enabled device
, but once the system restarts, the content set in the file will be overwritten!/etc/resolv.conf's comments explain very clearly that the fields that the user adds in/etc/resolv.conf are overwritten, overwriting the/etc/network/interfaces file with "Dns-nameservers" field lists the DNS server addresses. It is therefore preferable to set the "Dns-nameservers" field in the/etc/network/interfaces file to set D
First, the Linux server's default network card configuration file under/etc/sysconfig/network-scripts/, the general is the Ifcfg-eth0,eth0 to indicate a network card, eth1 represents the second, and so on.The detailed steps are as follows (with):1. Reach the
use the software directly in the virtual machine to operate the Linux system, you enter a LS to try* Then we configure the FileZilla Client, open the software, do the following configuration (hostname, user name, password, according to your own, the port number 22 fixed), finally click on the quick link, you can later through the software to the virtual machine system in the file copy transfer, of course,
Environment:HOST: Windows XPVMWare Version: 4.5.1Linux: Red Hat Linux 9
1. View network configuration information in the hostIn the CMD dialog box, enter ipconfig to obtain the network configuration of the host (Windows XP), as shown in:
2. Configure virtual machines ins
VMware Network Settings1.bridged (Bridging mode)If more than one IP address is available on the network, a bridging method is used. The IP addresses of the virtual machine and the host are independent of each other.2.NAT (network address translation mode)If only one IP address is available, use NAT mode. However, the external computer cannot access the virtual ma
default route:
Route add–net 0.0.0.0 netmask 0.0.0.0 GW 192.168.0.1
To delete a default route:
Route del–net 0.0.0.0 netmask 0.0.0.0 GW 192.168.0.1
Linux Routing configuration:
1, first turn on the routing function
Echo 1 >/proc/sys/net/ipv4/ip_forward (1 for open routing function, 0 for off routing function)
(In this experiment, just turn on the routing function OK)
2, other routing settings:
A,
In the work occasionally encountered in 1 machines configured 2 or more than 2 of the same network segment of the public network IP;In the actual configuration process found that when the configuration of multiple public IP network segment, only one public
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.