configuration, through the Graphical Network connection menu configuration. Dial-up Wireless and so on no condition experiment, does not involve. Main file:/etc/network/interfaces, here are some configuration of IP, gateway, mask, etc./etc/resolv.conf this file to save information about DNS Main command: sudo/etc/init.d/networking Restart restart the network to
Article title: FTPTelnetxmanager network configuration in Suse system. Linux is a technology channel of the IT lab in China. Including desktop applications, Linux system management, kernel research, embedded systems, open-source, and other basic categories of Suse network configuration
1. FTP configuration
We recom
Nbsp; network configuration in Suse I. vsftp is recommended for FTP configuration. if pure-ftpd is used, remove the pure-ftpd service. (1) the Root user executes yast2 --- networkservices -- and networkservices (inetd) to/usr/sbin/pure-ftpd and/usr/sbin/v
Network Configuration in Suse1. FTP configurationWe recommend that you use vsftp. if you use pure-ftpd, you m
Network Configuration in Suse
1. FTP Configuration
We recommend that you use vsftp. If you use pure-ftpd, you must disable the pure-ftpd service.
(1) the Root user executes yast2 --- network services -- network services (inetd)
Set/usr/sbin/pure-ftpd and/usr/sbin/vsftpd
Set the pure-ftp status to off and vsftpd st
network manager, through the upper right-hand corner of the Web Management applet can enable its configuration.This is a bit of a problem: it is shared with the second method of the configuration file, so it will cause a variety of conflicts, when used to pay attention to.Instead, both of these methods are configured, sudo/etc/init.d/networking Restart is enabled for the second method of configuration, and clicking on Auto eth0 in the
, without NFS)
Init 3 (full multiuser mode, multi-user mode, with NFS)
Init 4 (unused, retained)
Init 5 (X11, Gui multi-user mode)
Init 6 (reboot, do not set it to the system's initdefault)
ID: 5: initdefault:
6. Disable the Firewall
Modifying the firewall configuration file/etc/sysconfig/ipchains may be/etc/sysconfig/iptable,
Add the following content to the file header,
# If you want to use gnome/Kde, add the following line.
-A input-p udp-s 0/0-D 0/0 177-J accept
7. Reboot
Connection:
Open xm
CentOS to modify the network to modify a few files
1,/etc/sysconfig/network CentOS set host name and network configuration
For example:
Networking=yesHostname=oel6-69.localdomain2,/etc/sysconfig/network-scripts/ifcfg-eth0 for the specific network card settings
For example:
D
Before the SUSE Linux network card renaming problem, is installed on the virtual machine RAC, by replicating the virtual machine need to complete. Unlike Redhat Linux and Oralce Linux, the following records them for reference.
1, the new node network configuration
#启动节点之后没有任何IP配置信息
bo2dbp:~ # Ifconfig
Lo Link encap:local Loopback
inet addr:127.0.0.1 mask:255
The company has an suse linux server that requires two networks and one CIDR block is 192, which is used to go to the OP Management Platform System. One is B network, and the network segment is 202, which is used for Internet access. We all know that it is impossible for a computer to have two gateways, because the default gateway can only be one. If the gateway
Article title: Fedora network configuration tool system-config-network introduction. Linux is a technology channel of the IT lab in China. Including desktop applications, Linux system management, kernel research, embedded systems and open source, etc. This article mainly introduces the network configuration tool system
the Ifcfg-ethx file configuration is still in effect after the reboot, which is very useful in network management, and now I ifcfg-ethx the IPV4 network configuration method for a simple description of the file.Open commands and information according to the file Ifcfg-eth0 as follows:[[Email protected] ~]# Vi/etc/sysconfig/network-scripts/ifcfg-eth0 Device=eth0#
configuration file After modifying the network settings under Linux does not need to restart the computer, only need to restart the relevant settings options, network settings modified (such as the replacement of IP, domain, etc.): if it is redhat, restart the network can be entered service network restart or/etc/r
Create | network
If you find that easy Config does not start, and the original network service is working properly, you can create, modify, and delete network services in the following ways.
1 Create (Add a new network service)
Under your Oracle installation directory. \orac
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.