switch

Speed-limiting switches are typically on three or more switches, and the new switch model two-tier device since 2008 can achieve the QoS speed limit of 1Mbps, such as the Cisco 2960 series switches. After this, most of the domestic standard

Experiment on single-arm routing using a layer-3 Switch In the real environment, sometimes the gateway is not necessarily enabled on the router, sometimes the single-arm routing function is not necessarily connected to the interface on the router,

Today, the tutor told me about the company's network topology, related to the switch, the basic concept of routers and principles, I am not very clear, so on the internet to learn the information to learn a bit, and then feel that this article is

Two-layer switch: Two-layer switching technology is a mature development, two-layer switch is a data link layer device, can identify the MAC address information in the packet, according to the MAC address forwarding, and the MAC address and the

Two-tier switch:The second layer switching technology is more mature, two layer switch is a data link layer device, can identify the MAC address information in the packet, according to the MAC address to forward, and these MAC addresses and

* Vlan configuration ideas (access and Trunk) (1) create a Vlan and configure a static VLAN on an IOS-based switch: switch # vlandatabaseswitch (vlan) # vlanvlan-numnamevlan-nameswitch (vlan) # exitswitch # configureteriminalswitch (config) #

Absrtact: Spanning tree algorithms and protocols are the basis for automatically generating network topologies. This paper expounds the content of spanning tree algorithm and protocol, and gives the realization process in Ethernet switch. It is

Two-layer switching technology is a mature development, two-layer switch is a data link layer device, can identify the Mac in the packet Address information, forwarding based on MAC addresses, and recording these MAC addresses with corresponding

With the increasing popularity of Mbit/s, Gbit/s, and even Mbit/s local area networks, broadband MAN networks and even broadband wide area networks are widely used. Whether it is Intranet, exclusive, or residential intelligent networks, it is

1) layer-2 Exchange Technology The layer-2 switching technology is relatively mature. The layer-2 switch is a data link layer device that can identify MAC locations in data packets.Address information, which is forwarded based on the MAC address,

I'm going to go down to the two and three layers of the switch. A two-tier switch is equivalent to dividing an interface into multiple interfaces, just to provide a lot of interfaces; (if the landlord is not a professional person can ignore the

Slide switch effect css3 slide switch] Pure CSS3 code sliding switch effect-css3 sliding effect-css3 Slide left and right, css3-css3 Today, I saw a blog post on the css3 event and sorted out relevant materials on the rise. Click the button to slide

The Cisco3550EMI switch is used as an instance of the DHCP server project, and the cisco3550emidhcp Configuration of Cisco3550EMI switch as an instance of DHCP server Engineering Network Environment: A 3550EMI switch is divided into three VLANs.

The following article is an effective description of the ethernet switch parameter configuration problem, the switch according to the work protocol layer can be divided into a second layer of switches, third-tier switches and layer fourth switch,

Layer-4 switches are quite common, So I studied the basic knowledge and important technologies of layer-4 switches. I would like to share them with you here, hoping they will be useful to you. With the increasing popularity of Mbit/s, Gbit/s, and

Switch requirements 1. Switch to restore factory settings and its basic configuration. 1)//Enter privileged mode 2) del Config.text 2. Telnet mode to manage the switch. 1)//Enter the global configuration mode 2) enable password 0 [password] 3)

The author office used a common two-layer switch, has been silent for us for several years, so far there has been no accident. However, recently, the author of the local area network computer room has a switch suddenly strange phenomenon; taking

What is a fool switch? It is easy to understand the introduction is not to take care of its switch, connected to the network equipment can be used. With the development of modern society, the modern "lazy person" also more and more, those who light,

Switch Password settings: Switch>enable into privileged mode Switch#config terminal into global configuration mode Switch (config) #hostname set the host name of the Exchange Switch (config) #enable secret XXX To set the privileged encryption

Network Environment: A 3550EMI switch is divided into three VLANs. vlan2 is the network where the server is located and is named server. The IP address segment t-[/[Xm1S3 is 192.168.2.0, subnet mask: 255.255.255.0, Gateway: 192.168.2.1 the Domain