1. See how many hard drives are available#fdisk-LWell, in general, leave the system disk, the other disks if the size of the same, all together to do a raid.2. Decide what type of RAID to do.raid-0, Raid-1, raid-5?If you have three disks (or more) of the same size, it is highly recommended to
comparison of RAID common levels
Characteristics
Hard disk and capacity
Performance and safety
Typical applications
RAID 0
Used for parallel storage, that is, strips. The principle is to divide the continuous data into several pieces and then distribute it to each hard disk in the array. Any one disk failure will result in data loss.
Number of hard disks: one
Memo Http://baike.baidu.com/view/7102.htm
RAID is the abbreviation for "Redundant array of independent disk", which is an independent redundant array of disks. Redundant disk array technology was born in 1987 by the University of California, Berkeley.
RAID disk array (redundant array of independent disks)Simply explained, that is, the N-disk drive through the raid
Linux Performance Tuning 5: tuning an Important Role in soft raid storage. RAID independent redundant disk arrays are classified into two types: raid card-based hard raid (hardware implementation, high speed, suitable for large-scale applications), system-based soft raid (ge
Disk Array:
Disk Array (Redundant Arrays of Inexpensive Disks, raid) fault-tolerant Inexpensive Disk Array
Disk Arrays include hardware disk arrays and software disk arrays.
Disk arrays are classified into the following levels:
Raid-0 (equivalent mode): optimal performance
In this mode, disks of the same model and capacity are used for the best effect.
In this mode, rai
1. Install all SAS hard drive, boot up
2, the post process appears Ctrl + C prompts, press CTRL + C into LSI Logic Config Utility ...
Start SAS configuration
3, select the "SAS 1068" channel, press.
4, RAID select "Raid Properties", press
RAID Properties: Creating, managing arraysSAS topology: View Physical disk and
With the limitations of data security, performance, and capacity on a single disk, disk arrays (redundant Arrays of inexpensive/independent Disks,raid) appear, and RAID combines several separate disks in different ways, Form a disk group to achieve higher data security, performance, and capacity than a single disk.I. Common RAID levelsRAID has several levels of r
1. What is RAID?RAID is a fault-tolerant, inexpensive disk array that consolidates multiple small disks into a larger disk device that not only expands the capacity of the disk, but also enables data protection.2.RAID RatingRAID depending on the level of the implementation of the function and performance is also differentRAID0 requires at least two disks, dividin
Problem
In the case of power outages, the configuration of the already configured raid in the hard disk disk position swap, the power-on will not affect the integrity of the original storage data, will cause data disaster?
Answer
This depends on the RAID controller's firmware design, and one of the most important is, where is the raid information (
RAID server data Recovery Most failures are the loss of RAID array information, which causes the RAID server not to start and use, often requires the data recovery company to do RAID reorganization to function properly, from the data recovery point of view, the RAID server h
Disk Management mdash; RAID10 what is RAID10RAID10/01 is subdivided into RAID1 + 0 or RAID0 + 1. RAID1 + 0 is the first mirror and then split the data, and then all the hard disks are divided into two groups, which are regarded as the lowest combination of RAID0, and then the two groups are considered as the operation of raid1. RAID 0 + 1 is... Disk Management-RAID 10 What is
Terms
RAIDAn independent redundant disk array is a storage term. to improve performance and reliability, multiple disks are combined, which is a storage unit from the outside. the detailed introduction to RAID is not within the scope of this document; Wikipedia article "RAID" provides better content.
Hard RAIDHard RAID is a R
Recently, we have a server that requires RAID. So today we will discuss how to install CentOS to RAID.There was a lot of nonsense in the front, mainly taking notes for yourself. laruence quickly clicked the upper right corner of the cross.First, because the motherboard chip is not supported, the cold blog did not successfully install hard RAID. For hard RAID, the
Arrays are divided into soft RAID and hard RAID. Soft RAID is implemented by the system based on partitions. Hard RAID is a hard disk operation object, with RAID cards to implement the system environment: RHEL6.3x86 _ 64 This section describes the first step of Soft
Tags: RAID LVM disk partition partitioning tool file systemfirst, disk basic knowledge1, disk and hard disk are all the unified address of the disk storage system. When the disk is working, the head is suspended in a radial motion above the disk platter, without touching each other.2. Purchase Disk:(1) Spindle speed speed fast (r/min), 5400/7200/10000/15000;(2) interface type:sata/sas/scsi/ide; SAS usage in the enterprise environment is more common .(
Raid:Common RAID levels:RAID 0:Operating mode: The data is striped first, and then stored to the hard disk.Space utilization: 100%Whether redundancy is supported: noPerformance: Disk IO increased (depending on the number of disks)Requires at least 2 disksRAID 1:Operating mode: There is a disk for the mirror diskSpace utilization: 1/2Whether redundancy is supported: YesPerformance: Write performance degraded, read performance unchangedRequires at least
RAID overview RAID is short for RedundantArrayofInexpensiveDisk. with this technology, multiple disks can be integrated into one array and can be used as a single disk. The RAID disk array can be used to improve data read/write efficiency and data redundancy (backup) based on different technologies. when a disk in the array fails, data can be restored from other
Several RAID Modes
1. RAID0
That is, Data Stripping Data sharding technology. RAID 0 can connect multiple hard disks into a larger hard disk group to improve disk performance and throughput. RAID 0 has no redundancy or error repair capability. It is low in cost and requires at least two disks. Generally, RAID 0 is used
1. Disk Management#提示没有partprobeYum-y Install parted#新硬盘新建分区 and change the type to Linux Raid AutoDetect#非交互方式, note that there is a enter key between 1 and TFDISK/DEV/SDE Fdisk.txt:NP11TFdW#新建分区, note that there is a return enter between 1 and WFDISK/DEV/SDF Fdisk.txt:NP11WQ#将磁盘格式化为ext4文件系统Mkfs.ext4/dev/sde#2. Radi Management#以两块硬盘做raid0,-l0 says Raid0,-n2 says raid with 2 hard drives#-a answer all prompt
I. What is Raid?
Raid was called in the Early Days: Redundant Arrays of Inexpensive Disks Fault-Tolerant cheap disk Array. Now it is called Redundent Array of Independent Disks and fault-tolerant Independent disk Array. This is a storage module that combines multiple hard disks and features fault tolerance. It can be simply understood as a combination of several small hard disks into a large hard disk with
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.