In the wireless network environment, the access terminal needs to be authenticated and billed, in order to meet the demand, TL-AC1000 provides the corresponding authentication and billing interface in Portal certification. Users can access the third party authentication server according to the demand, and can also use the AC built-in authentication server to carry on the authentication billing.
tl-
Puling tl-wr886n (V2-V3) set up wireless bridge introduction
The tl-wr886n routers currently have V2.0, V3.0, V4.0, V5.0 versions, where the V2.0 and V3.0 versions of the tl-wr886n router have the same wireless bridging.
To view the version number of the tl-wr886n router
You can find the Ver (that is, version/versio
solution to the general tl-wr886n set up after the network can not be a way to check the success of the Internet settings
After you log on to the Settings page, click "Run Status"--> and then in the right interface, there is a "WAN status" option.
If the IP address, subnet mask, gateway, and DNS options below the WAN Status option Show all 0, the connection to the tl-wr886n, or the settings are problemati
PU tl-wr847n 300M wireless Router setup Step one: tl-wr847n router installation
The newly purchased Tp-link tl-wr847n 300M Wireless router, from the device connection to the completion of the Internet configuration, requires the following 3 configuration procedures: 1, tl-wr847n router installation, 2, set
Cascade tl-wr845n Router WDS Bridge setup Step 1
To view the wireless parameters of the main router, enter the settings interface of the master router to view and record: Wireless signal name, wireless encryption mode, wireless password, wireless channel (channel please set one manually), as shown in the following figure:
Cascade tl-wr845n Router WDS Bridge Setup Step 2
Login
General tl-wr886n Set the wireless password step one, login to the Settings page
Enter tplogin.cn--> in the browser in the Jump page, enter: Administrator password, login to the TL-WR886N Settings page.
V1-v3 Version tl-wr886n login page
V4-V5 Version tl-wr886n login page
Pay attention to th
Solution Tp-link tl-wdr5600 cannot use 5G network method one, router on 5G wireless network setup Improper
1, check whether the 5G wireless network has been enabled
In the tl-wdr5600 router Setup interface, click on the "Common settings"--> "Wireless Settings"--> and then look at the "5G Wireless status" option to enable, as shown in the following figure. If it is turned off, turn on the 5G wireless netwo
Universal tl-wr886n Set MAC address filtering step one, view your wireless device MAC address
For example, a user's network is often stolen by others, even if set a wireless password is the same, at this time we can configure wireless MAC address filtering to solve this problem, only let users own computers, mobile phones can surf the internet, other wireless devices are not allowed to surf the internet.
1. View the MAC address of the notebook compu
the method of solving the TL-WA832RE amplification Radio signal unsuccessful
If you set the Tp-link Tl-wa832re extended (amplified) wireless signal, the LEDs on the tl-wa832re are red and illuminated steady, indicating that the tl-wa832re extension (amplified) wireless signal is unsuccessful, please install the method
General tl-wdr5600 Upgrade firmware considerations
(1), before the upgrade operation, please connect the computer with the network cable and Tp-link tl-wdr5600 router, do not use the wireless way to connect
(2), the firmware upgrade process, the need to ensure the stability of the router power supply, in the process of upgrading must not power, or damage your Tp-link
Tp-link tl-wdr6500 Router 5G setting bridge step one, record main router wireless parameters
Please confirm and record the wireless signal name, wireless password and wireless channel of the main router, this article uses the following parameters for example:
Viewing wireless parameters for the primary router
Note: Here we call the wireless router that is already available on the Internet the main router.
Tp-link
Step One, demand analysis of setting speed limit for tl-wr886n (V2-V3)
You can find the Ver (that is, the version/version) in the serial Number column on the label at the bottom of the tl-wr886n router, which is the hardware version. The following figure
View the hardware version of tl-wr886n
Please make sure that you limit which one, or the number
tl-wr941n 450M Wireless Router setup diagram Step one: tl-wr941n router installation
1, telephone line users: Please prepare 2 short network cable, a network cable used to connect ADSL modem or light cat on the network cable interface and TL-WR941N router on the WAN interface, another network cable, one connected to the computer, the other end of the
set Tp-link tl-wdr6300 5G Wireless WDS bridging mode Step one, view the main router information
Enter the settings interface of the master router (the router that is already connected to the Internet) to view the wireless signal name (SSID), encryption mode, wireless password, channel parameters of the primary router, as shown in the following illustration. Ssid. zhangsan_5g Wireless Encryption method. WPA-PSK/WPA2-PSK wireless password. 1A2B3C4D, wi
after we enter tplogin.cn (or 192.168.1.1) in the Browser, a dialog box pops up asking for an admin password, but we don't know what the admin password is? How do I input it?
The steps are as follows:
However, many users do not know what the Tp-link tl-wr842n administrator password is, so they cannot log on to the setup interface of the Tp-link tl-wr842n router. The following is a detailed description o
The following describes the quick setting method in TL-WR700N Router mode.I PCNetwork parameter settingsNote:TL-WR700NThere is only one wired interface, which connects the network cable to the front-end device and servesWANPort. Because the computer cannot be connectedWANYou need to connect to the wireless router for configuration.TL-WR700N by default does not enable DHCP server, cannot automatically assign an IP address for the computer, so you need
tl-wr886n v2-v3 Set Virtual Server step One, example list
On the bottom tab of the TL-WR886N router, locate the Ver (that is, the version/version) in the serial number column, which is the hardware version. The following figure.
Check Hardware version
A small enterprise uses the tl-wr886n router to connect to the Internet, and constructs the web, F
tl-wr740n Router firmware upgrade diagram Step 1
To view the hardware version of the tl-wr740n router
1, after the tl-wr740n router upgrade software, the router may revert to the factory default settings, all existing settings information will be lost, it is recommended to back up the existing settings before upgrading the software information.
2,
tl-wr2041+ Set IP Bandwidth control diagram Step one: Set the computer IP address
Tp-link tl-wr2041+ routers restrict network speed topology
Example analysis
A user home for 4M ADSL Broadband, the home has desktops, notebooks, mobile phones and many other devices; Desktop is mainly used to watch video, play games, so the need to ensure that the desktop computer has enough broadband resources,
To set the method:
1, the computer wirelessly connected to the tl-tr761 2000L;
2, the computer landing tl-tr761 2000L Management interface (http://192.168.1.1), in the " Storage Control " Page Selection "WiFi Shared mode " , click Save.
the following separate Windows , Android , IOS three operating systems are examples of how other wireless terminals access shared resources.
Windows operations ( Fo
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.