Environment: Raspbian-stretch (2018-06-27)Raspberry Pi: 3 generation B Type1, Raspberry Pi equipment, need to be in the field can also have independent networking capabilities, it is necessary to use the Internet of Things module.The SIM868 communication module for micro-snow is used here, such as:2, will SIM868 insert
Adafruit Raspberry Pi Tutorial Lesson five: Using the control cableTime 2014-05-09 01:11:20 geek Fan Original http://www.geekfan.net/9095/ Theme Raspberry Pi MacOS Linux This article is translated from adafruit.com by Geek fan-boyd Wang. Welcome to the Geek Translation team and join us in translating and sharing. Plea
there are two i²c devices connected to the bus, and their addresses are 0x48 and 0x77 respectively. If you do not see a device, check the hardware connection, and remember to open the system config inside the i²c.Then still the sample code:
Import time
Import SMBus
addr=0x48
cmd=0xab
# open/dviev/i2c-1
bus = SMBus. SMBus (1)
# Read and write data, Case 1 Data
= bus.read_byte (addr)
bus.write_byte (addr, data+1)
# Read and write data, Case 2
= Bus.read_byte_data (addr, cmd)
bus.write_byte_dat
Tags: serve using more than open installation method to run the LAN via spanThe person who can see this blog note that the attempt failed, will find that the memory card after the flash into Ubuntu, unable to operate the Raspberry Pi via ssh. It is because the official Ubuntu system needs to set something for the first time, similar to the initial startup of Windows, if not set up, even the operation accoun
General Purpose Input Output (Universal input/output) abbreviated as GPIO, or bus extender, simplifies the expansion of I/O ports with industry standard I²C, SMBus, or SPI interfaces. GPIO products provide additional control and monitoring capabilities when the microcontroller or chipset does not have enough I/O ports or when the system requires remote serial communication or control.This article has nothing to say, mainly stickers! But this article i
Reference: RPi Serial ConnectionThis article from: Http://www.raspberry-projects.com/pi/programming-in-c/uart-serial-port/using-the-uartUsing the UARTIf you is running Raspbian or similar then the UART would be used as a serial console. Using a suitable cable, such as the Ttl
1 , configuration options:The first time a Raspberry Pi is used, a simple configuration is required to run the following command in command-line mode:$sudo Raspi-configThe new and old version of the configuration interface is not the same, the following list of two kinds of more common:
Expand_rootfs – Extend the root partition to the entire SD card (the Raspbe
http://blog.csdn.net/rk2900/article/details/8632713/Raspberry Pi first launch raiders for MACMade by RkThanks to the Zhejiang University "embedded System" course to provide strong support!/************************************************************************/This tutorial connects the MacBook via the serial port, and the notebook side operates the
Raspberry Pi ------For Windows
Step 1:in Order to write the image for sd,we should download and install image Writer for Windows
Step 2:download and install putty and connected to serial port
Step 3:plug in the power then start Raspberry Pi and
If you have not logged on to the Common graphic user interface, This method is suitable for setting Raspberry Pi's wifi. Especially when you do not have a screen or wired network, you only use the serial control line. In addition, this method does not require additional software, and everything is included in Raspberry Pi
Reference: http://programmingadvent.blogspot.hk/2012/12/raspberry-pi-uart-with-pyserial.htmlRaspberry Pi UART with pyserial os:occidentalis v0.2Hardware:raspberry Pi Revision B with CobblerSetup:serial Loopback (Connect RX and TX pins on GPIO pins)Linux attempts to treat all devices as file system like devices, the UAR
the digital tube. The correspondence depends on the order in which you send the data when you wire and write the code.
DS is a serial input pin, so-called serial is to make the data on a signal line in order to transmit one by one, like a string of candied fruit. This pin we received from the Raspberry Pi at any
Use the command line to set Raspberry Pi's Wi-Fi network
If you have not logged on to the Common graphic user interface, This method is suitable for setting Raspberry Pi's wifi. Especially when you do not have a screen or wired network, you only use the serial control line. In addition, this method does not require additional software, and everything is included
is also created in the Raspberry Pi "/dev" directory, where the Bluetooth indicator of the Arduino is blinking, which means "not connected", and when the Raspberry Pi sends a message to the Bluetooth device, it does the connection operation.Unbind a Bluetooth device that is already tied to the Arduinosudo 0 xx:+:£ ºAf
First, hardware preparation(1), Raspberry Pi Pi2(2), 8G 10-speed Micro SD card(3), LCD display (if the VGA interface, need to add an HDMI to VGA module)(4), mouse(5), the installation of Windows 10 PC (requires physical direct installation, not virtual machine mode, this article is not required)Second, software preparation(1), Windows IoT Raspberry
/opt/ros/indigo
Common errors:
The compilation process compiles more than 180 package and installs it in the/opt/ros/indigo directory, often reporting ' collada_parser ', ' collada_urdf ', ' Rviz ', ' Visualization_ Tutorials ', ' rqt_robot_plugins/rqt_rviz ' these packets are faulty and the installation is interrupted. The solution is to remove the packages from the directory ~/ROS_CATKIN_WS/SRC directory and recompile the entire Ros. Finally, a separate workspace is created and the packages a
My girlfriend sent me a Raspberry Pi (Raspberry PI) as a birthday present. Get started with a simple experience. Borrowed a roommate's Kingston 4g SD card, plus a network cable. Get ready to do it!The official NOOBS was first downloaded .
NOOBS (new out of Box software) is a new setup program that makes it easy
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.