unable to open mtp device

1. Go to the Device Manager.Right-click MTP with a yellow question mark and select "property" and "details" and "device sample ID" (use Ctrl + C to copy ).2. Find c: \ windows \ INF \ wpdmtp. inf to open (or open through running), and find[Generic. ntx86]% Genericmtp. device

From: http://robert.penz.name/658/howto-access-mtp-devices-via-usb-on-ubuntu-12-04/ A friend asked me how he can access his Nexus 7 device via USB on his Ubuntu 12.04 notebook. with Android versions below 4.0 that was simple as the device registered as mass storage device. the problem now is the stock Ubuntu 12.04 doe

After installing the palm synchronization software in Windows 2003, 680 is always recognized as an MTP device, even after you manually update the USB driver (USB _driver in the palm installation directory.Some people say that you can disable the synchronization of the ptunes computer. My system did not even install the ptunes software after this flash. Finally found a solution today1. Find the

Enter the C:\Windows\System32 directorySearch Wpdmtp.inf This file, you should be searching out two Wpdmtp.infDirectly right-click the first wpdmtp.inf this file, select InstallIf the prompt installation succeeds, the Representative has successfully repaired, and MTP is normal again.If the service installation paragraph in the prompt INF is invalid, select the second wpdmtp.inf to continue with the right-click installationYou should now be prompted fo

First of all, my situation, of course, anxious people can skip this paragraph. The newly installed Win 7 32-bit system, then Xiaomi 3 directly connected to the computer, should be automatically loaded with the driver. After I was normal on the computer to open the memory operation of the mobile phone copy and paste cut, and then the hands of the cheap, after the completion of want to safely quit the connection, point off the

WIN8 System open Device Manager appears umdf HID minidriver device unknown device How to deal with? after installing the WIN8 operating system, open the Setup Manager to check whether the driver is intact, open

Reason:Is that the virtual machine service is not turned onWorkaround: (Run as Administrator)Click "Start → run", enter CMD in the Run box to open a command prompt, then execute the following command in turn.net start VMCInet start vmx86net start Vmnetuserifsc config Vmci=autosc config Vmx86=autosc config Vmnetuserif=autoVMware cannot open the kernel device "\\.\

:s3c2410_serial1 at MMIO 0x50004000 (IRQ = $) is a s3c2440S3c2440-uart.2:s3c2410_serial2 at MMIO 0x50008000 (IRQ = ON) is a s3c2440Loop:module LoadedDriver ' SD ' needs updating-please use bus_type methodsCs89x0:cs89x0_probe (0x0)Cs89x0.c:v2.4.3-pre1 Russell Nelson eth0:cs8900 Rev J found at 0xc4a00300cs89x0:extended EEPROM checksum Bad and no Cirrus EEPROM, relying on command lineCs89x0 Media IRQ, programmed I/O, MAC 08:89:89:89:89:89CS89X0_PROBE1 () successfulS3c24xx NAND Driver, (c) 2004 Simt

These two days in the study of Linux input-polldev.c, which is a new architecture provided by kernel, the architecture based on the original Linux input subsystem, added a layer of polling device encapsulation outside the input device. This architecture allows us to register a poll-Dev. We only need to provide this poll-dev with a polling interval and a polling callback function, then the system registers a

server available, giving up.VFS: Unable to mount root FS via NFS, trying floppy.VFS: cannot open root device "mtdblock2" or unknown-block (2, 0)Please append a correct "root =" Boot option; here are the available partitions:Kernel panic-not syncing: VFS: Unable to mount root FS on unknown-block (2, 0) [Solution process] 1. I thought there was no/dev/mtdblock2 device