usb debugging meaning

Method One: Click "Settings" on your phone to see that there is a "help setting"-"Developer Tools", and then directly find the USB debug mode on it, which is much simpler than the Android system, as shown in the following illustration. Method Two: Enter the phone interface directly input "*#* #6961 #*#", access to the USB interface, we click on to open. Method Three: Note and

1 we found the "Setup" in the Red Meter note "system" and there will be a "about cell phone" in the phone's system. 2 We click on "about the phone" and then we will see you "Android version", now we just click on the Android version four times, then there will be the USB developers you want the option of OH. 3) Now we return to the mobile home page, then also click "Settings" in the settings inside now there is a "developer option" Click to ente

1 in the Millet 2S desktop to find "settings" and then we click to enter, and then see below there is a "developer option" Now we click on it to enter. 2 Then we find "USB debugging" after entering the interface to open it, when we open will pop up a prompt, the content is "whether to allow USB debugging" click OK.

1 We click on the mobile desktop "settings" and then find "about the phone" to enter after the click "More" specific as the figure. 2) and then we find the version number, and then we click on 4 consecutive times, and then from "General"-"more". 3 good so in more inside will see there is a "developer option, and finally the USB debugging appears Summarize In fact, all Android 4.2 and later version

To enable the hidden "developer options" and "USB debugging" options, follow these steps:1. Click the application icon on the standby page.2. Click set ].3. Click general and about devices ].4. Move up the right-side screen and click internal version number seven times until the prompt "developer mode enabled" is displayed ".5. You can see [developer options ]. Click devel

Yun-Habitat community small tip you, if you do not need to use like a mobile phone helper to install software or download software we do not need to turn on the USB mode, this USB debugging mode is the developer option OH. 1. Open the Samsung S5USB Debug mode is very simple, we click on the phone "application." 2. Find "Set" here click on it (because we

If you want to connect to the 91 assistant and other related software must turn on the USB debugging section, we operate the method is very simple, click on the Phone "application" (Note on the Phone desktop standby state). 2. Then we find the application below the "set" icon to click on it to enter. 3. Here we will see there is a "about the device" click on it to enter. 4. Then in

1 We first click on the phone "settings" and then into the Vivo xshot mobile phone "about the phone" interface. 2 In addition, we open the "about the phone" continuously non-stop click Version number, until the phone prompts "you are in the developer mode, do not need to do this" we can not click. 3) Then we go back to the "setup" of the phone just now and you will see there is a "developer option" we click on it to go in again here to find "USB

1 First, we will open the developer selection, enter the phone "settings" and click "About the Phone" click on open Access. (pictured below) 2 After we click on the phone in the "version number", see the ScreenTip "You are in the developer mode!" "No, then we'll go back to the Settings page and we can find the developer option at the bottom." (pictured below) Now to open the USB mode, we click on the mobile desktop "Settings", drop-down m

1. We click "Settings" in the phone and then click "About Mobile" to open the entry, details as follows 2. Then we click on 2 consecutive times version number 3. Then we click on until "Open developer Mode" as shown in the following figure. 4. Then we click on the settings and find "developer Options" as shown in the following figure 5. OK, we'll go to the phone's "Developer option" and check "USB

1.Oppo R3 Interface Click "Settings" into "General" and then open "about the phone", click "More". 2. Click on the "version number" in the Open Interface 4 times in a row, then we click "More" in the "normal" interface. 3. Click "Developer Options" to activate "USB debugging". Tips: The above open USB debugging

1 in the Mobile desktop Click "Settings" and then open the Open interface to click "Advanced Settings" to enter, as shown in the following figure. 2 then enter the "Advanced settings" you will see there is a "developer option" We click on the "Developer Option" will be entered into the phone-related interface will see a "USB debugging", now we open on it. Friendly Tips Hammer Phone Android 4.4 system

1. This handset uses the Android 4.3 system, 2013 on the market, but the Samsung handset's setup interface all the same, we clicked "the application". 2. Here you will see a "set" click on it to enter. 3. Then we click on "General" as shown in the picture. 4. Then we click on the open interface of the "about device" entry. 5. After opening, you will see a "build number" with our fingers constantly clicking on th

1. Click "Set" in the Note4 mobile interface and find the "more" inside, then there will be a "about the device" and then we'll click on it. 2. OK now after we get into "about the device" we will see "build Number" and then click on "Build Number" and then stop after "No need, developer mode enabled." 3. OK then we click "Settings" and you will see that there is a "developer option" Now we click on "Developer Options" to enter, the "USB

1. We first need to switch on the mobile phone on the USB debugging, first in the mobile phone desktop to find the "application" as shown in the picture. 2. Then we'll find the "Set" button and click Enter. 3. Then click on the "More" button as shown in the following figure. 4. Well, in more, you'll see a "about the device" panel. 5. In the click into the device we will see a

1 We first click on the phone "settings"-"about" see it. 2 Now we click on the entry to the details interface, then find "software information" in the About and then click on it, then we find "version number" and then we click 5 consecutive times that will show "you are in the developer mode" 3 After this prompted our USB opened, we return to the phone's settings to find "developer Options" and then click into the "Developer Options" interface w

1 in vivo we open the desktop "settings" and then find "about the phone" we click on it to open. 2 in the "About mobile" page We found the "version number" continuous click, waiting for your screen display "You are in the developer mode, do not need to do this" can not stop clicking. 3 OK now we have USB turned on, I now go back to the phone desktop click "Settings" and then you will see a "developer option" then we click on "Developer Options"