As an Android technology home, USB OTG is what you must understand, so-called USB OTG is you can use the phone or tablet to charge, and the computer to transfer data from the Micro USB interface to connect other USB peripherals, s
(Original works, reproduced please indicate the path of reprint)Recently on the MStar 786 platform, there is a need, that is, the USB OTG converted to a host USB drive.Start debugging, thought as long as the OTG configuration removed, that is, CONFIG_USB_MS_OTG shield off, b
peripheral) H2. inA-role (default host), the H2 itself supplies 8mA.
The "mini-AB" connector is compatible with standard USB 2.0 "mini-B" connectors, which appear in some new USB peripherals.
Most OMAP processors support this and similar product designs.Register interfaces to the different USB controllers are largely
1. Overview OTG devices use the ID pin in the plug to differentiate A/b device,id ground is known as A-device, the USB host,a-device at the time of the connection always provides power to the bus, the ID floating is called the B-device, the connection time of the USB Devices, the device's
) time. A_hnp_support: Compatibility feature of earlier OTG versions. setting this feature indicates that a-device of the B-device peer supports HNP. A-device should set this feature for B-device if a-device supports HNP. A_alt_hnp_support: discard getstatus (). The OTG status bit in the data section is host request flag, indicating that the current
1. OverviewThe OTG device uses the ID pin in the plug to differentiate A/b device,ID GroundKnown as A-device, for connection time.USB Host, A-device always provides power to the bus,ID DanglingKnown as B-device, for connection time.USB Device, the device's USB HOST/USB devic
are complete, the two OTG devices can transmit information in the host and slave mode respectively. The master-slave role exchange process of the two devices is defined by the host transmission protocol (HNP.
1.1 initial functions of the host (Adevice) and slave (Bdevice)
The initial function of a device is implement
This is a creation in
Article, where the information may have evolved or changed.
ID
(
Identification
) role Identification pin
two x USB when the device interconnects, how to make two devices know: Who is the master control? Who is peripheral"periphery"? This actually uses the new PIN, which is appended with the fifth pin in the traditional 4-pin USB interface:ID
to be the master of mutual vaccinationUS
1 Introduction With the release of USB, USB has become a standard interface. Currently, USB supports three transmission modes: low speed (1.5 Mb/s), full speed (12 Mb/s), and fast (480 Mb/s: block Transmission, synchronous transmission, interrupted transmission, and control transmission. USB is flexible and convenient
1 IntroductionWith the publication of the USB2.0 version number, USB is becoming more and more popular and has become a standard interface. Today, USB supports three transmission rates: Low speed (1.5mb/s), Full speed (12mb/s) and Fast (480MB/S), four transport types: block transfer, synchronous transmission, interrupt transmission, and control transmission. USB
STM32 Usb-fs-device Development KitCompatible with the stm32f102xx and stm32f103xx series, STM32 L1 Ultra Low P Ower, STM32 F3 SeriesUSB on-the-go host and device libraryCompatible with the stm32f105x, stm32f107x devices in FS USB modesCompatible with the stm32f2xx and stm32f4xx devices in HS and FS USB modesCompat
A USB pin typically four lines, defined as follows:To support OTG features, the Mini/micro USB interface extends an ID pin (4th foot)A device-side ID foot is grounded, the initial state is host, such as PC and the OTG device support deviceb device-side ID foot is dangling, d
The so-called USB OTG feature, which allows Windows Phone devices to connect to the flash drive, external USB hard drive, keyboard, or even mouse, via a USB interface, usually requires a special wiring connection.
Some Windows Mobile devices have already supported USB
-----------------------------------------------------------------------------------------------------------------------Shell shield drain WireBytes -----------------------------------------------------------------------------------------------------------------------
Standard A is the most common type. Most USB mouse and keyboard connectors are of this type. You can directly Insert the standard a connector tacle (master) on the PC ). The biggest bene
compatibility is poor, when using a partial USB device crashes, reinstall its driver try. 3, the USB interface is artificially corrupted, or the connection is incorrect. 4, in the actualIn the process, the USB device, in turn, plugs into the USB connector, of course, but will be the
When using the PS minimum system built on Zedboard in Vivado (2015.4.2), the USB-OTG fails to function properly and errors in the startup log.After a comparison with each of the original startup files, it was determined that the bit out of the Vivado project was out of the question. This means that the construction works are wrong.USB Boot error message: External PHY chip initialization failed, loading modu
Tags: gpio dir direct GRE reset development err Echo StatusThe last time I talked about USB not booting was caused by the incorrect configuration of the Emio pin in the Vivado project, and how is this pin used on the software? First, the Linux SDK provided by Xilinx already contains gpio drivers and Sysfs to match, and the OTG-RESETN is configured and declared in the device tree file. Second, in practical u
一个线程中进行Viii. OtherAs a normal developer, if there is no USB device, then the debug program is a problem.You can use the Adbtest program to connect two phones or tablets with an OTG cable.A colleague with a USB device will encode according to the protocol rules of the device. This is used to convert byte to other types, as well as hexadecimal problems.Concrete ana
follows:result = mUsbDeviceConnection.bulkTransfer(mUsbEndpointOut, mData, (int1500);//需要在另一个线程中进行Viii. OtherAs a normal developer, if there is no USB device, then the debug program is a problem.You can use the Adbtest program to connect two phones or tablets with an OTG cable.A colleague with a USB device will encode according to the protocol rules of the devic
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.