Tutorial on TCP/IP Subnet Mask
1. Default class A, B, and C addresses, subnet mask;
Ii. Role of subnet mask:IP address 192.20.15.5 11000000 00010100 00001111 00000101Subnet Mask 255.255.0.0 11111111 11111111 00000000 00000000Netwo
, infrared, etc., sometimes referred to as physical media. The MAC address is also called the physical address, hardware address, or link address, which is written by the network device manufacturer when it is produced inside the hardware. This address is not related to the network, that is, regardless of the hardware with this address (such as network cards, hubs, routers, etc.) access to the network where, it has the same MAC address, MAC address is generally immutable, can not be set by the u
Reference Original address: http://www.cnblogs.com/JuneWang/p/3917697.htmlIP Address:IPv4IP address = network number + host numberSubnet Mask:A subnet mask is a basis for determining whether the IP addresses of any two computers belong to the same subnet . The simplest understanding is that the respective IP addresses of the two computers and the
Transferred from: http://www.cnblogs.com/JuneWang/p/3917697.htmlIn order to learn more about the TCP/IP protocol, recently read a lot of relevant information, collected and recorded as follows, for later use and convenient for you to learn:IP address, subnet mask, default gateway, what does DNS server mean?(a) Problem analysis001. Q: IP address, subnet
PS: found a good article on the Internet, carried over, in case you can't find it later. At the same time the individual made a simple change. IP address, subnet mask, default gateway, what does DNS server mean?(a) Problem analysis001. Q: IP address, subnet mask, default gateway, DNS server, what is the difference? I k
are suitable for small networks such as campus networks, and each class C network can have up to 254 hosts.
From the above introduction we know that the IP address is the network number and host number to indicate the host on the network, only in a network number under the computer can be "directly" interoperability,
computers with different network numbers need to be connected through gateways. But such a division appears and is very inflexible in some cases. For this reason, the IP network
me with the analysis!
Saidi network IT technology community moderator "Sebei" opened the answer for the netizen harcsbg.
For question 1, the simple question is complicated by you. Why do we need to use a subnet mask to divide network segments? If it is 255.255.255.0, it means that 254 hosts can access the internet. If you change it to 255.255.255.192, it means that only 62 hosts belong to the same network
You must know something about the IP address, right? We know that the TCP/IP protocol that is widely used in the Internet is to differentiate between different hosts by using IPs. If you've ever had a TCP/IP protocol set up, then you're bound to encounter the term subnet mask (Subnet mask), so do you know what a
Subnet mask (subnet mask) definitionIt is a bitmask that indicates which bits of an IP address identify the subnet on which the host resides and which bits identify the host. The subnet mask
The most direct role of the subnet mask is to determine whether the IP address is within the same network segment as another IP address.
Here is a simple look at the basic configuration of IP on a computer
IP Address: 192.168.0.5
Subnet Mask: 255.255.255.0
Default gateway: 192.168.0.1
Example above, IP address,
Http://www.knowsky.com/383893.html
Subnet Mask, the concept and working principle of the gateway and ARP Protocol are several important knowledge points that Beginners first encounter when learning network knowledge, among them, the role and basic working principle of subnet mask and ARP protocol is also the key and di
1. How many subnets will be generated
The X power of 2-2 (X represents the mask bit, that is, the part of the binary system that is 1. In the current network,-2 is no longer required and can be used in all, however, you need to add the corresponding configuration commands. For example, you can use all the commands by adding the IP subnet zero command to the Cisco router .)
Note: I have read a lot of boo
Subnet Mask and IP address calculation network address and broadcast address conversion
IP Address: 202.112.14.20.Subnet Mask: Too Many Subnet MaskWhat is the network address and broadcast address of this host?Solution:Step 1: Determine the network bit and host bit.
Tag: In this example, two locks return ref strictly implementing window
Directory
Default Gateway
Network Address, host address
Gateway
Subnet Mask
Broadcast address
Special IP Address
Refer:
Default Gateway
A configuration item used for TCP/IP protocol is the IP address of an IP router that can be directly reached. To configure the default gateway, you can create a default path in the IP route ta
. The four IP addresses are divided into two parts: the network number and the host number: the number of network numbers directly determines the number of network numbers that can be allocated (calculation method 2 ^ number of network numbers) the number of host numbers determines the maximum number of hosts in the network (calculation method 2 ^ number of host numbers-2). According to the Npower of 2, it is converted to a 10-digit system that is easy to understand. '/17' indicates 11111111.111
All the calculation and application of the subnet mask are based on the binary, so we should focus on the binary form of The netmask. Generally, we can view the IP attribute in decimal format. in order to make it easier for users to watch, in fact, computers use binary methods to calculate and use subnet masks,
A common IP address is composed of a network ID and
IP address, subnet mask, default gateway, what does the DNS server mean? IP address, subnet mask, default gateway, what does the DNS server mean?(a) problem analysis001. Q: IP address, subnet mask, default gateway, DNS server, wha
First of all, our premise is the local area network, so we mentioned the modification more specifically, is to find the subnet mask and the default gateway for proper padding.
Here are two specific ways to do this:
Method One, we find any other networked computer on the same LAN, locate and double-click the local connected Internet Protocol (TCP/IP) entry, and populate the
Not much to say, directly on the code.
Package com.ckw.test;
Import Java.io.BufferedReader;
Import java.io.IOException;
Import Java.io.InputStreamReader;
Import java.util.*;
Import Java.util.Map.Entry;
public class Testofsubnetmask {map
The results are:
---------------------------------------------------------------Windows IP Configuration host name ............. : DADI primary DNS suffix ........... : node type ............: mixed IP routing enabled ..........: no WINS agent enable
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.