vboot

/home/lianghuiyong/linux_share/arm-qte-4.6.3-20100802.tar.gz4>> Decompression installation BusyBox source code# cd/opt/friendlyarm/mini2440# tar Xvzf/home/lianghuiyong/linux_share/busybox-1.13.3-mini2440.tgz5>> unpacking and installing the Linux sample program# cd/opt/friendlyarm/mini2440# tar Xvzf/home/lianghuiyong/linux_share/examples-20100108.tgz6>> Decompression installation Vboot source code# cd/opt/friendlyarm/mini2440# tar Xvzf/home/lianghuiyon

; unzip and install embedded graphics system QtE-4.6.1 source code# Cd/opt/FriendlyARM/mini2440# Tar xvzf/home/lianghuiyong/Linux_share/arm-qte-4.6.3-20100802.tar.gz4> decompress and install the busybox source code# Cd/opt/FriendlyARM/mini2440# Tar xvzf/home/lianghuiyong/Linux_share/busybox-1.13.3-mini2440.tgz5> decompress and install the Linux sample program# Cd/opt/FriendlyARM/mini2440# Tar xvzf/home/lianghuiyong/Linux_share/examples-20100108.tgz6> decompress and install the

Http://bbs.wuyou.net/forum.php?mod=viewthreadtid=363198extra=Install Ghost version XP to VHD with Grub4dos+firadisk (succeeded)Because Vboot menu bad, compatibility is not very good, cracked version some can only recognize 500M memory, so do not want to use Vboot.To install the ghost version of XP to the VHD with Grub4dos+firadisk without formatting the original system disk, the following steps are now successful:1, Tools: Grub4dos,firadisk Drive Pack

1, # BDFVerify that the file system usage is less than 90%2, # ioscan-FN-fncdisk-fncprocessor-fnclanView All Io Devices3, # lanscanView Nic running status4, # ifconfig lanxMake sure that the network card is configured with the correct address and mask5, # netstat-RnConfirm that the route is configured correctly6, # swlistDiscover all installed software7, # swlist-l fileset-a stateCheck that all installed file sets are in configured status.8, # kmtuneAll parameters are correctly configured.9, # l

.tar.gzFile system source code: BUSYBOX-1.13.3-MINI2440.TGZTest instance Program source code: EXAMPLES-20100108.TAR.GZBoot loader source code: vboot-src-20100106.tar.gzBootloader.tgzTarget file System source code: ROOT_QTOPIA-20100108.TAR.GZVarious tools for developing your needs:Target file system Image authoring Tool Mkyaffs2image: Make the Root_qtopia directory into an image file (can be burned into the target board)Mkyaffs2image.tgzInstall logo ma

Screen capture shortcut keysActions: Saving to-shortcut keysFull Screen capture-desktop (. pdf file): Command + SHIFT + 3Screen part screen-desktop (. pdf file): Command + SHIFT + 4Windows, Icons-desktop (. pdf file): 1. Command + SHIFT + 4 2. SpaceFull Screen Capture-Clipboard: Ctrl + COMMAND + SHIFT + 3Screen part screen-clipboard: Ctrl + COMMAND + SHIFT + 4window, Icon-clipboard: 1. CTRL + COMMAND + SHIFT + 4 2. SpaceAction:-Shortcut keysprogram Freeze shortcut keysStop process-command + deci

size (MB) 8704Current le 272Allocated PE 544.Used PV 2 --- Physical volumes ---PV name/dev/DSK/c0t6d0s2PV status availableTotal PE 4346Free PE 3181Autoswitch onProactive polling on PV name/dev/DSK/c2t6d0s2PV status availableTotal PE 4346Free PE 3181Autoswitch onProactive polling on 13. Verify that the bdra was updated properly. Take note of the HW pathsStep 14.# Lvlnboot-VBoot definitions for volume group/dev/vg00:Physical volumes belonging in root v

NAND Flash Start 4 kb To SRAM , In this way NAND Flash Start . If Bootloader Less 4 kb Words (like Vboot ), In SRAM You can Boot , Greater 4 kb Words ( U-boot , Vivi ) , In SRAM Do 1 After some basic initialization Bootloader To SDRAM Li ( > 0x30000000 ). // ================================================ ================================================= // Note: Bootloader It is a small program that runs before the operating system kernel runs. Th

cannot be accessed randomly like nor flash or memory, it cannot be an EIP (running on a chip), so it cannot be directly used as a boot. In the S3C2440, the bootloader is started on the NAND Flash, because there is a built-in sram in the S3C2440 called stepping stone (stepping stone, very good image ...), After the system starts power-on, it will copy the starting 4 kb of content on the NAND flash to the SRAM for execution, so that it can start from the NAND Flash. If the bootloader is smaller t

Detailed steps of mirror Disk 1. Create a boot LVM disk that will be used as an image# Pvcreate-B/dev/rdsk/c2t2d0 2. Add the hard disk to the current volume group.# Vgextend vg00/dev/DSK/c2t2d0 3. Set as the boot disk# Mkboot/dev/rdsk/c2t2d0 4. Test the correct auto file to the new lif area.# Mkboot-a "HPUX-SCSI"/STAND/vmunix "/dev/rdsk/c2t2d0 5. mirror each LV separately# Lvextend-M 1/dev/vg00/lvol1/dev/DSK/c2t2d0# Lvextend-M 1/dev/vg00/lvol2/dev/DSK/c2t2d0.....# Lvextend-M 1/dev/vg00/lvol8/dev

internal structure is roughly the following :1.Nor Flash has its own address lines and data lines, can be similar to the memory of random access, nor flash can be directly run the program, so nor flash can be used directly to boot, nor Flash will be launched when the address mapped to 0x00. MINI2440 is directly to the directly burn the Vivi on NOR Flash.2.Nand Flash is an IO device, data, address, control lines are common, need to control the software zone reading timing, so can not be like nor

Jumpstart installation, this installation is normal.2) encountered BUG6437646 during installationAfter installing the SOLARIS10U10 with Jumpstart, the machine will hang in the optical drive after reboot. The following is the details of the boot process {0} OK boot-vboot device:/[emailprotected]/[emailprotected]/[emailprotected]/[email Protected]/[emailprotected]/[emailprotected],0:a File and args:-vmodule/platform/sun4v/kernel/sparcv9 /unix:text at