Full solution D-LINK Switch configuration in the enterprise network VLAN subnet usage, on the D-LINK Switch configuration problems, from the following aspects: from the enterprise network plan four VLAN subnet classification and structure, DES-3326SR Switch configuration process is introduced. The example below gives a
for virtual networks. In particular, it not only supports traditional port-based VLAN division, but also supports VLAN division based on IP addresses, subnet numbers, and protocol types, this brings great convenience to campus network management.
Therefore, the new layer-3 Exchange router is used as the main device in the LAN of the campus and building. In addit
using ASIC hardware to achieve routing and switching at line speed, the latter represents the fast ip of 3com, and the virtual fast Security Network of cabletron. The method used is to route the network at the first layer, then, the second layer switches the end-to-end network stream data group. This is the policy of "one route, then switch.
The powerful functions of the layer-3 Exchange router are as follows:
1) routes are calculated based on the L3 protocol. The supported routing protocols i
One, the question650) this.width=650; "src=" http://s2.51cto.com/wyfs02/M02/82/73/wKiom1dVYe-Dqy8CAAAgd6TFaKM711.jpg "title=" 12.jpg "alt=" Wkiom1dvye-dqy8caaagd6tfakm711.jpg "/>PC1 network segment for 192.168.1.1/24, PC2 network segment for 192.168.1.2/24SW1 's E0/1 and E0/2 are zoned vlan10.Can two PCs interoperate?Answer: No interoperability, VLAN only valid for localSecondly, the problem650) this.width=650; "src=" http://s2.51cto.com/wyfs02/M00/82
virtual IP, however, the benefit of VLAN implementation is that it can be linked to an existing three-layer switch or directly to the trunk of a standard IEEE 802.1q-enabled device.
Mechanism platform, strategy opera. Now that the VLAN implementation Mechanism has been clear to the chest, then its shortcomings are estimated you also see, how to overcome it? Pvlan said the real is a
flow rules.(6) Finally, the Neutron L2 Agent will run an RPC loop task to handle port additions, deletions, and modifications when it is started. The administrator can specify the execution interval for the RPC looping task through the configuration item polling_interval, which defaults to 2 seconds.2.3 Create a virtual network and subnet 2.3.1 Create command[Email protected]:~$ neutron net-create net1 (or Admin user running neutron net-create net1--
Aggregation (VLAN Aggregation) technology, it allows hosts in different VLANs connected to the same vswitch and in the same IP segment to use the same default gateway for layer-3 communication. We know that in a common VLAN, even if all VLANs are in the same IP segment, a VLAN interface IP address must be configured for each
departments into different VLANs and map VLANs to different IP subnets. Therefore, the IP subnet policy is applicable to scenarios with low security requirements, network Design with high demands for mobility and simple management. The following command is usually used to set an IP subnet policy VLAN:
Vlan 1 ip addres
ports to be a VLAN, and to configure IP addresses for that VLAN, then the computer in that VLAN is the gateway and the other VLANs cannot be on the same subnet as the VLAN.(4) VLAN partitioning based on IP multicast (built on the
[Translation] IP subnet division
Original article title: IP subnetting made easy
Address: http://articles.techrepublic.com.com/5100-10878_11-6089187.html
IP network engineers need to have a solid understanding of how IP subnet division works. however, this topic is often ignored by instructors and the students are very confused and nervous about it. george ou developed a simple, graphical method to explain
Super-vlan :
Achieve two-layer isolation, three-layer interoperability;
all the Sub-vlan all three-tier communication needs to pass Super-vlan this gateway to implement;
in a large network, saving IP Resources. VLAN communication can be achieved by simply configuring the Super-
First, the generation of Super VLAN backgroundIsolate-user-vlan successfully solved the problem of reducing the number of VLANs, and also realized the sharing of three-layer gateways to some extent. But it also has a problem with MAC address duplication that consumes MAC address table entries, and the technology itself belongs to a two layer VLAN technology.In a
Jane's going to talk Super VLAN-conserving IP address isolation two layer communication VLAN aggregation in the implementation of the different Sub-vlan to share a subnet segment address, but also brought Sub-vlan between the three-layer forwarding problem. Want to do the DH
Transferred from:
Http://bbs.51cto.com/thread-68584-1-1.html
Subnet Mask and subnet divisionDirectory:I. SummaryIi. Concepts and functions of subnet mask3. Why do I need to use the subnet mask?4. How to obtain the Network/Host address using the subnet maskV. Classification
Subnet Mask and subnet division
Directory:I. SummaryIi. Concepts and functions of subnet mask3. Why do I need to use the subnet mask?4. How to obtain the Network/Host address using the subnet maskV. Classification of subnet masksV
subnet mask and subnet partitioningDirectory:
I. Summary
The concept and function of subnet mask
Third, why do I need to use the subnet mask
Four, how to use the subnet mask to get network/host address
Five, the classification of subnet
Directory:I. SummaryIi. Concepts and functions of subnet mask3. Why do I need to use the subnet mask?4. How to obtain the Network/Host address using the subnet maskV. Classification of subnet masksVi. subnet addressing technology7. How to divide subnets and determine
... Increased virtual IP, however, the benefit of VLAN implementation is that it can be linked to an existing three-layer switch or directly to the trunk of a standard IEEE 802.1q-enabled device.Mechanism platform, strategy opera. Now that the VLAN implementation Mechanism has been clear to the chest, then its shortcomings are estimated you also see, how to overcome it? Pvlan said the real is a
I. Concepts and functions of two subnet masks 3. Why do I need to use a subnet mask 4. How do I use a subnet mask to obtain a network/Host address 5? What is the classification of a subnet mask 6. subnet addressing technology 7. How to divide subnets and determine about how
A summary of the concept and function of two-subnet mask how to use subnet mask four how to get network/host address by subnet mask classification of five subnet masks six subnet addressing technology seven how to divide subnets and determine
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.