vmware vsan configuration

machine's IP address. Of course, before configuring the gateway and subnet mask for NAT, this VMware comes with a tool: Vmware-netcfg, located under the VMware installation folder. The default should be in/usr/lib/vmware/bin/vmware-netcfg. To open with Super User privileges

The clone function in VMware is quite good. Fast and convenient. vmware needs to re-encapsulate SID After cloning the Windows operating system.Otherwise, there will be many conflicts when the two systems run simultaneously.Www.2cto.comIn Linux, the cloned system cannot use the NIC normally. MAC address conflicts ....Next we will introduce a very convenient and simple method. To sum up, after cloning it comp

This kind of configuration everyone has written a lot, I would like to summarize, mainly to the problems I encountered to write.Process:One, virtual machine (VMWARE+XP) configuration1. Modify the boot. ini file to add the following code at the end of the file:multi (0) disk (0) rdisk (0) partition (1) \windows= "Microsoft WINDOWS XP Professional Debug"/noexecute=optin/fastdetect/ debug/debugport=com1/baudra

Read a lot about other people to configure the virtual machine online method, are not very useful. Before looking for a lot of information on the Internet, it took a long time to solve the internet problem. Now want to write something, put my fast configuration Linux Internet method to share:Note: This machine uses the CentOS6.5 inside is the application SECURECRT connection. Do not use DHCP to automatically assign IP addresses, or you will need to lo

Preparatory work:Download:1, vmware-workstation-full-10.0.0-12959802, Centos-7-x86_64-dvd-1511.isoInstallation:1, vmware-workstation-full-10.0.0-1295980, here to provide a registration code 5F29M-48312-8ZDF9-A8A5K-2AM0Z.2. Create a new empty virtual machine, as shown below:The installation is complete after the next step.3. Insert the image file:It's done.4. The ISO installation is now started. Turn on the

Unfortunately, the bios of VMware does not recognize the USB boot device, even if the USB device is connected.The solution to this problem is to add the hard drive directly, the hard drive pointing to the physical hard disk, the USB setting.Note: Under Ubuntu to set this feature requires the use of sudo vmware to run.The following are the setup steps for Windows, and Ubuntu is broadly consistent:Switch to t

Here's how it works:Software Environment: VMware Workstation 10.0 Virtual Machine CentOS 6.5 physical Machine Windows71, first enter the original system, use the command to view the network card information#ifconfigDefault system boot does not load network card, see eth0 information650) this.width=650; "src=" Http://www.linuxidc.com/upload/2015_03/15031418132128.jpg "alt=" VMware Virtual machine cloning Cen

1. Type of network adapter for the virtual machine, select Host-only. Modifying the network adapter type at startup requires a power-off restart.2. Local PC settings, the network neighbor enables VMware virtual Ethernet Adapter for VMnet1 (hont-only), IP auto-acquisition, and the property--high-level network connection Sharing.When the local network card is turned on for sharing, the IP address of the VMNET1 virtual network card will be automatically

first turn off the firewallHost (host machine Win7)Virtual Machine (XP)3. Important: If the ping does not work first consider the problem with the firewall!!!VMware Configuration:Nat Mode play:1. Configure the NAT virtual network card:2. Configure 2 IP for virtual machine: one for SSH connection with real machine, one for connection with external network environment download file, query, browse Web, etc...From for notes (Wiz)

VMware is a very popular virtual machine that is frequently used in our daily work. This article briefly summarizes the three network configuration methods used in normal times. The specific principles are not discussed in detail. The virtual machine system is installed in Linux. First, we can view all network configuration connections on the local machine and ru

the host, this step is very important3, next open the virtual machine, the connection mode to bridge, the replication physical network connection status is optional, on-demand selection4, the last step, the virtual machine in the CentOS network configuration, the main changes in the following aspects: Ipaddr,broadcast,gateway, there is a point to note that the last of IPAddr is a custom, but must not be in the same network with other people in the en

client, so naturally it cannot be modified.Well, with the above understanding, I believe you should guess the problem is that the real server itself has 192.168.123.123 IP address. So the data that has been processed is sent directly to the 192.168.123.1! As follows:Client access [192.168.123.100], LVS server forwarding [192.168.100.11]- Real server return [192.168.123.1] -Client does not recognize this return.The solution is to switch off the 192.168.123.101 network card on the real server, an

One, configure the second NIC 1) "CentOS6.5 Configuration Network" (http://blog.csdn.net/clevercode/article/details/46376985);How to configure Eth0. This article explains the configuration of eth1 in a virtual machine.2) First to the eth0:192.168.142.130 virtual machine, add a second network card device. Select the virtual machine, right-click Settings, and add the network adapter.3)

A network card configuration experience in centos on vmware encountered a problem with the network settings of a linux virtual machine. The record is as follows, which is also used for reference by students with the same experience. The purpose is to configure the network interface of the Bridge Mode on vmware9 + centos5.8. The environment is installed with vmware9 on win7 and runs the centos5.8 Virtual Mac

The problem with my whole morning was that the configuration file was reversed in order to cause the shared storage configuration to be unsuccessfulthe virtual machine in the Vmx file is last filled in: (Must be all at the end, the order is immutable, otherwise unsuccessful!) When you are finished modifying, turn off the virtual machine software re-open to take effect. disk.locking = "FALSE"disklib.datacach

VMware is already familiar to users, VMware ESXi is also called (VMware vsphere Hypervisor), VMware ESXi is a streamlined and free version of VMware ESX, and the installation configuration is very convenient and simple, so it is f

Bridging mode:In this mode, the virtual operating system in the virtual machine is a separate host in the LANNat Mode:In NAT mode, the virtual system needs to remember the NAT (Network transform) function, and access the public network through the host and the network it resides in. The TCP/IP configuration information for the virtual system in NAT mode is provided by the DHCP server of the VMNET8 (NAT) virtual network and cannot be modified manually,

We are often in the VMware environment to replicate the virtual machine operations, such as we build clusters and so on, and in the replication, configure the network, we will always find such a problem, Nic no matter what, is not up. Now let me share one of my processes with you. 1. Modify the network card configuration file, use and source host (source host is cloned mother) different IP address/etc/sys