/localhost.localdomain:2.log# here to note: Each user can start their own vncserver Remote Desktop, while each user can start multiple vncserver Remote Desktop, they use IP port number: ip:1, Ip:2, Ip:3 to identify, differentiate, and use the same port will automatically exit the logged-in user. Another, the big part o
1. First, check whether desktop access is installed.Yum groupinstall "X Window System"Yum groupinstall "GNOME Desktop Environment"VNC (Virtual Network Computing) Virtual Network Computing tool is essentially a remote display system. The administrator can not only view the desktop
How to Use Xmanager and VNC to log on to the Remote Desktop and xmanagervnc to log on
There are two common methods to call Remote Desktop: Xmanager and VNC.
Just today, I had a click, and it was sorted as follows:
Xmanager
Xmanage
the VNC server program on the remote Linux host and then install the VNC client on my own laptop in Windows, and finally make a remote Desktop Connection(1) server-side installation:[[email protected] ~]# rpm-q vnc-serverpackage
VNC was developed by the ATT laboratory and is an excellent remote control tool software. Later, it was open-source in the form of GPL authorization. After several years of development, the current VNC does not refer to a software, but the general name of a software. The following describes two commonly used VNC softwa
installed on your server)
1. check whether VNC is installed in linux.
Enter the following command in the terminal window:
rpm -q vnc-server
The returned information is as follows:
package vnc-server is not installed
The vnc server is not installed.
2. run the following command for installation:
yum install
Linux (CentOS6.3) sets up VNC Remote Desktop Connection. I just studied Linux and selected the CentOS6.3 system. as I started to study Linux, I had a lot of detours for this Remote Desktop Connection, which made everyone laugh. To get this
desktops.Password:Verify:
You will be prompted to enter the password, which is required for remote logon. Enter the password and press Enter.
4. Switch to the root account: su root and enter the password of the root account.
Vi/etc/sysconfig/vncservers # vnc configuration fileVNCSERVERS = "10000: root" # cancel the previous #10000: root desktop number: User)
SUSE LINUX ENTERPRISE SERVER 64BIT uses VNC for graphical interface Remote Desktop control, the following steps:1. Enable SuSE remote controlSuSE installs VNC by default, opens YaST, Network Service, remote management (remotely ad
RHEL5 uses remote desktop VNC-Linux Enterprise Application-Linux server application information. The following is a detailed description. VNC (Virtual Network Computing) Virtual Network Computing tool is essentially a remote display system. The administrator can not only vie
Linux installation setup VNC Remote Desktop Connection to install Oracle 11g
Preface:To install Oracle in Linux, you need to start the swing interface of Java. Therefore, the x-window is required. Therefore, it is difficult to directly go to the server room to perform on-site operations. Remote xshell cannot run Window
VNC Server and VNC Viewer support a variety of operating systems, such as the Unix family (Unix,linux,solaris, etc.), Windows and MacOS, so that VNC server and VNC Viewer is installed separately in different operating systems for control. If the current operating master computer does not have the
Linux (CentOS 6.3) sets up VNC Remote Desktop Connection. I just studied Linux and chose CentOS6.3. Since I started to study Linux, I had a lot of detours for this Remote Desktop Connection, which made everyone laugh. To get this VNC
How can I remotely control the centOS desktop? How to remotely control centOS desktop CentOS using windows
1. check whether vnc is installed on the local machine (vnc is installed on centOS5 by default)
Rpm-q vnc-server
If the result is:
Package
To connect to the Linux desktop, VNC connects to the Linux Remote Desktop and, following the steps below, it is very simple, fast, and Linux configures VNC (for example, Redhat, CentOS, Fedora Series).Linux Platform Installation VncserverWindows platform uses
http://www.linuxidc.com/Linux/2013-04/82510.htm
Configure and install http://www.linuxidc.com/Linux/2013-05/83975.htm for VNC under CentOS
VNC remote control installation and setup http://www.linuxidc.com/Linux/2013-01/77769.htm
Windows Access Ubuntu http://www.linuxidc.com/Linux/2012-10/73043.htm through VNC
Install
We plan to configure vncserver to manage the server in root remote desktop mode. The following is the basic configuration process: 1. first check whether the vnc service is installed, if installed, do not need the second step of Operation # rpm-q | grepvnc-server2. because I didn't install it before, now I use yum... we plan to configure vncserver to manage the s
installed, run the following command to install it:Yum install tigervnc-server-yCheck the installation[Root @ linuxidc rpms] # rpm-qa | grep vncTigervnc-1.1.0-16.el6.CentOS.x86_64Tigervnc-server-1.1.0-16.el6.centos.x86_64Libvncserver-0.9.7-4.el6.x86_64[Root @ linuxidc rpms] #
3. The configuration after installation is incorrect. Run the following command to edit the configuration file:Vim/etc/sysconfig/vncserversVNCSERVERS = "1: root"VNCSERVERARGS [1] = "-geometry 800x600"
The following section
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.