vs f6k pfc3c

(nightly OK12 0001.64f8.3180 to 0001.64f8.318f 0.105 12.1 (5r) 12.1 (nightly OK13 0001.64f8.3190 to 0001.64f8.319f 0.105 12.1 (5r) 12.1 (nightly OKMod Sub-Module Model Serial Hw Status--------------------------------------------------------------------------1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2SAD044509Y3 1.1Ok2 Policy Feature Card 2 WS-F6K-PFC2 SAD04130A17 0.305 OK2 Cat6k MSFC 2 daughterboard WS-

1Switch-2 (config) # interface range Tengigabitethernet 3/1-2Switch-2 (config-if) # Channel-group mode onSwitch-2 (config-if) # no shutdown4. Convert chassis into Virtual Switch mode1) Check the chassis PFC mode to ensure the same 2 chassisStep 1switch-1# Show platform hardware PFC modeEnsures that the PFC operating mode matches on both chassis, to ensure that the VSS comes up in SSO redundancy mode.Step 2switch-2# Show platform hardware PFC modeStep 3Switch-1 (config) # Platform hardware VSL P

802.3afTwo power supply modes are supported., 1236Or4578. Supported5Power level: 0: Default15.4 million1:4 W2:7 W3:15.4 million4: Undefined, extended. CiscoThe previous Ethernet power supply is6.3 millionCisco's earlier Ethernet power supply technology is as follows: Power panelUse45,78Power supply. Inline powerUse12,36Power supply, need to combineCDP. Fully supported802.3afThe product is as follows: Catalytic 6000Platform: WS-X6148-45AFWS-X6148-21AFSub-cards required:WS-

on the two switches matches, confirming that VSS is in SSO modecisco-2#show Platform Hardware PFC mode//Verify that the PFC operation mode on the two switches matches, confirming that VSS is in SSO modecisco-1# Platform Hardware VSL PFC mode pfc3c//set the PFC operation mode for switch 1 to PFC3C, which is optionalcisco-2# Platform Hardware VSL PFC mode pfc3c//F

802.3AF supports two modes of power supply, 1236 or 4578. Supports 5 power supply levels: 0: Default 15.4W 1:4w 2:7w 3:15.4w 4: Not defined, extended use. Cisco's previous Ethernet power was 6.3W Cisco's previous Ethernet ┑ paragraph 跞, lt;br/>power panel uses 45, 78 power. The inline power uses 12, 36, and needs to be combined with CDP. Full support for 802.3AF products are as follows: Catalyst 6000 Platform: Ws-x6148-45af Ws-x6148-21af Need to add a child card: WS-

Virtual link 1VSS-SW1 (config-if) #no shut 6509-2 Configuration vss-sw2#conf TVss-sw2 (config) #interface Portchannel 2VSS-SW2 (config-if) #switch Virtual link 2VSS-SW2 (config-if) #no shut Physical interfaces are zoned into port groups VSS-SW1 (config) #interface RangeTengigabitethernet 5/4-5VSS-SW1 (config-if-range) #Channelgroup 1 mode onVSS-SW1 (config-if-range) #no shut switch-1# Platform Hardware VSL PFC mode

PFC3C mode switch-1(config) # Platform hardware VSL PFC mode Pfc3cswitch- 2(config) # Platform hardware VSL PFC mode pfc3c can be viewed in PFC mode via show platform hardware PFC mode. Switch-1# switch Convert mode virtualswitch-2# switch Convert mode Virtual device restarts when VSS is converted and is VSS mode when boot is complete6. Configure dual-Live detection (EPAGP mode)Router (config) # interface

With your password. Use the no shutdown command on interfaces that are being used. If you use the show ip interface brief command, every interface that you want to use shocould be up. Type config-register 0x2102 Press Ctrl-Z to leave the configuration mode. The prompt is now hostname # Type write memory or copy running-config startup-confi G to commit the changes. Example of a Password Recovery on the Catalyst 6000 MSFC Module Switch (enable) show module

-F6K-MSFC ok3 3 48 10/100BaseTX Ethernet WS-X6248-RJ-45 ok4 4 8 1000BaseX Ethernet WS-X6408-GBIC ok5 5 2 MM OC-12 ATM WS-X6101-OC12-MMF ok Mod Module-Name Serial-Num--- ------------------- -----------1 SAD0342313315 SAD034145633 SAD032427374 SAD032201525 SAD03433465