wipe drive from bios

Computer BIOS does not detect the hard drive what to do 1, plug in a U disk, and then use the General PE Toolbox to make the U disk into a startup disk. 2, after the successful production, restart the computer continuously press the Hot key (not clear hot key point here) into the BIOS system, in the BIOS system set U

If the serial hard disk is hooked up to the interface controlled by the onboard serial control chip, it is easier to set up. Take the P4C800 board PDC20378 serial control chip as an example, connect the serial hard disk and boot into the BIOS. Open the onboard serial controller switch in operating mode under the Advanced menu and set a good working mode. If set to IED, it will enter IDE mode after startup. When all the settings are complete,

First, the way to enter the BIOS according to the type of BIOS is also different, the most commonly used is the boot has been holding down the "Del" key to enter the BIOS, the interface is mostly the following figure: Mobile ↑↓←→ cursor keys can be selected, the general set up the boot sequence of items in the "Advanced

Keep the original data as much as possible and establish a UEFI and BIOS dual-boot PE USB flash drive1, make sure that the USB drive or the mobile hard disk has a FAT32 partition, if there is no FAT32 partition, use the AO Mei Partition helper or ppm to convert an existing partition to FAT32 partition 0x0c, or create a new FAT32 partition, Then extract the UEFI-enabled Win8pe.iso to the partition.2, use Boo

:= ' 0 '; End; End The following function gets the BIOS number {*************************************** author/date:description: Gets the BIOS number ********} function getbiosnum:string; Var biosdate,biosname,biosversion,biosnum,bioscopyright:string; Begin Try Biosdate:=string (Pchar (PTR ($ffff 5)); Biosname:=string (Pchar (PTR ($ffa 68))); Biosversion:=string (Pchar (PTR ($fe 061)

HP Notebooks Setting the hard drive IDE/AHCI mode in the EFI BIOS 1, after the boot continuously press F10 or ESC key, press F10 to enter the BIOS, move around or with the mouse to click System configurations; 2, under the system configurations select device configurations; 3, according to the need to select the corresponding hard disk working

HP Workstation PC clears hard drive data via UEFI BIOS 1, the boot appears HP logo press Esc key into the "Startup menu" interface; 2, select "Security Erase" option, press ENTER; 3. Select the hard drive to clear the data and press ENTER; 4, then prompted the warning, the main content is that the hard disk data will be emptied, this op

the BIOS sets the method and procedure for the CD drive to boot. Methods/steps are as follows: 1, turn on the computer power, in the computer appears the first screen information, according to the information on the screen prompts, press the corresponding key to enter the COMs settings interface. Depending on the motherboard model, there may be different ways to enter the CMOS interface. Howe

and ending at 3. respectively: HDD-0, HDD-1, HDD-2, HDD-3 General machines, only one hard drive. You said the choice of HDD-1, desktop icons will soon come out, is your hard drive to connect the line is the second hard drive wiring ~ ~ So HDD-1 data faster HDD-0 is your first hard drive connection. When it accesses t

BIOS is one of the most basic computer settings, but also one of the most basic configuration of the computer, it is a computer in the motherboard on a ROM chip program, the main function is to provide the computer with the most direct hardware settings and control. It's not hard to see that the BIOS setup contains a lot of things, but there are some things that are not very useful. For example, the small s

Lenovo ThinkPad E420 installed SSD to the CD-ROM drive bit, the BIOS can not find, PE to find SSD. Download old peaches PE version installed to U disk, start with U disk, enter WinPE, install system to SSD hard drive, reboot, BIOS can't find SSD hard drive, so will not st

If you have two hard drives in your system, you must set them up in the BIOS to work properly. In the BIOS main interface Select Standard CMOS features entry, press "Enter" key to enter. If you want to set the first hard disk as the primary, select the user entry in the IDE Primary master type (hard disk) and set mode (hard drive mode) to LBA. Sets the ID