xterm windows

What is a shell?Simply put, the shell is a small program that can accept commands from the keyboard and send them to the operating system, and then the system executes. In the past, this was the only interactive operation available on computers that had UNIX installed. Now, you can use a graphical interface to enter the command line, such as the shell.On most Linux computers, there is a Bourne called Bash (Bash is a shorthand for the Again shell, an upgrade of an early shell written by Steve Bou

A command is used in LInux to completely solve the problem of Xterm Chinese display. The terminal is always indispensable. Generally, terminals are relatively large and slow. Xterm is very good, but its Chinese font is displayed incorrectly by default. after looking for it for a long time, it is all about modifying this configuration, changing the final sum of that file... A command is used in LInux to com

Friends who often use command lines such as Putty or xterm to control Linux systems may encounter problems like mine: When you press ctrl+s, the command line does not respond at all. Then close the window and reopen it, which is very uncomfortable, and now we're going to solve the problem. As long as the first editor you use is not vim, or a friend of Emacs, the most frequently used shortcuts in the editing process are probably ctrl+s. And for those

A command completely solves the problem of xterm Chinese display Source: Internet Author: self-learning network CLICK: 190 A command completely solves the problem of xterm Chinese display Using a Linux system, terminals are always indispensable. Generally, terminals are relatively large and slow. Xterm is

Recently, the teacher asked me to process multi-threaded server development on QT under Ubuntu. Although I only called the network module of qt, in order to avoid the trouble, I wrote the console program in QT, but the following occurs when I run the program. The program is running, but there is only one cursor on the console. Due to Baidu's incorrect posture, it took a lot of time to understand that qt creator does not support Gnome default terminal gnome-terminal. Therefore, you need to switch

A command is used in LInux to completely solve the problem of Xterm Chinese display. The terminal is always indispensable. Generally, terminals are relatively large and slow. Xterm is very good, but its Chinese font is displayed incorrectly by default. It has been found for a long time and is used to change this configuration,I finally solved the problem by modifying the file. The following command is simpl

your favourite text editor. After line, add the line: export display=:0 Save and exit. Close Xquartz if its running. Now Dia should come up. If It does not come up, try restarting your computer. If not, try and add the line-Export display=:0To your ~/.bash_profile, re-login and hopefully you should has Dia working once again. Let me know if this helped your out:) The red rectangle shows where I put the DISPLAY variable for Dia to start re

When accessing the name server through some bastion machines, the following error message appears when connecting via SECURECRT:650) this.width=650; "height=" 175 "title=" image "style=" Border:0px;padding-top:0px;padding-right:0px;padding-left : 0px;background-image:none; "alt=" image "src=" http://s3.51cto.com/wyfs02/M01/6F/66/ Wkiol1wbbhwylcyaaagemms0mm8060.jpg "border=" 0 "/>Here's how to fix it:1. In the shown, select the Session option650) this.width=650; "height=" 357 "title=" image "styl

The solution that the QT console program cannot run under Ubuntu and how to configure XtermRecently, because the teacher asked to be in the Ubuntu Qt on the process of multi-threaded server development, although only a simple call QT network module, but in order to avoid trouble, I am still very fucked in the QT Under the console program, but after the completion of the program to run after the following situation occurs.The program runs, but there's only one cursor in the console that jumps and

As long as the first editor you use is not vim, or a friend of Emacs, the most frequently used shortcuts in the editing process are probably ctrl+s. And for those who often use putty or xterm to control Linux, Unix systems, I'm afraid I often encounter the same problem, instinctively pressed the ctrl+s, found that the command line is completely unresponsive. Helpless, you can only reopen the window and reopen the new command line interface.Each time y

error Because the Redis service is self-booting, it will not start again, so loading the configuration file is a failure. There is also no Redis boot small box (below the picture, slowly looking down), note that the Windows version of the Redis installation, the default boot loaded configuration file is redis.windows-service.conf, as shown in:2. Invalid passwordAlthough the password is set in the configuration file (redis.windows.conf), the password

enter the name of the task in the saved session.5. Double-click Open, the screen appears, so you can use putty.Three Putty use techniques of course, the most basic use of the knowledge described above, common use methods and techniques are:1. Chinese input support Putty also support Chinese input, to set up: window->; appearence->; font:change->; Arial, character set selection chinese_gb2312. 2. Color Display Support Putty also supports color display directory, executable files, ordinary files,

========================================================== ====================================== Iii. Common Use of xming First: Use xming through SSH 1. AdvantagesUsing the X11 forwardig function of SSH, you can simply use xming in the following three steps, and the communication between X Server and X client is encrypted. 2. configuration steps Step 1: Use Putty to connect to X client (192.168.0.50)Enable the X11 forwarding function (for example) to connect to the remote X client Step 2: En

From: http://www.cnblogs.com/procoder/archive/2009/04/13/Windows_Mobile_Index.html By Jacob Lin (Lin Yongjian)Windows Phone, Windows Mobile, Windows Embedded CE (WinCE ),. NET Compact Framework, Native C ++ Development Series (hundreds of original articles are constantly updated and improved) due to work relationships, we are now focusing on

Due to work relationships, we are now focusing on Windows Phone, Windows Embedded Ce (wince), and Windows Mobile ,. NET Compact framework, native C ++ development, summarize some work experience and knowledge, Article Will continue to improve. About me, Jackie Lin. Windows Phone Mircosoft officially renamed

PHP 5.4 has a built-in Web server that is handy for native development because you no longer have to install Web server software like Apache, you can launch PHP's Web server directly from the command line. The startup method is simple, enter the directory where the project is located at the command line, and then use the-s parameter to start the service, you need to specify the host address and port, and all the request information will be displayed in the console window as shown in: Shortcut T

Scope of use: SharePoint Foundation 2010 | SharePoint Server content of this article Step 1: Select and pre-configure the operating system Step 2: Install Prerequisites for SharePoint 2010 Step 3: Install SharePoint 2010 Step 4: Install Visual Studio 2010 and Developer Documentation Step 5: Create a Hyper-V image from an installed system When you create or customize a SharePoint solution, it is often best to develop such a solution on a local computer that has Microsoft SharePoint Serve

xterm to Xterm-color 3. Create a shortcut to a task putty can create a Windows shortcut for a frequently visited site. To create a method: First select Putty.exe, right click the mouse, send to get the desktop. Then right-click the shortcut, select Properties, and change the shortcut-target-"c:/putty.exe" to "C:/putty.exe @mysession" 4. Copy and paste in the Put