How to retrieve the IP address of a wireless router

Through various methods, we finally found the IP address of the wireless router. I hope this method will suit you. In the following article, we will also introduce the DHCP service. Note that the IP address must be in the same CIDR block as the router, and the gateway and DNS must be set to the IP address of the wireless router.

Where is the IP address of the wireless router?

Follow the settings. I hope you can succeed. I. The current vro settings are mostly set through the WEB. Because the vro may not be available until it is correctly set, therefore, we connect to the vro through a network cable. First, enter the WR541G default IP address, 192.168.1.1, in the address bar of the browser. The default IP addresses of the vro may be different. Therefore, you can find the default IP addresses in the vro or instructions. Here, you need to note: when setting a router through the WEB, the IP address of the computer connected to the router must be set to the same gateway as the router; if the IP address of the wireless router is 192.168.1.1, you can set the IP address of the computer to 192.168.1.2 --- 192.168.1.255.

You can set the IP address of a computer as follows: when the NIC Driver is correctly installed on the computer, select control panel-network connection-local connection, for example, Internet protocol TCP/IP ), click properties -- select to use the following IP address; enter 192.168.1.2 --- any address between 192.168.1.255, enter 192.168.1.2 here, enter 255.255.255.0 as the subnet mask, and enter 192.168.1.1 as the default gateway. For example, enter the IP address of the vro in the address bar of the browser and set 192.168.1.1 to enter the WEB Settings page of The vro. Generally, the router requires the administrator password when entering the WEB Settings interface. For the first time, enter the original password as instructed.

Enter the correct user name and password to go to the wireless router IP Address Settings page. TP-LINK router setup and installation is simple, and cost-effective is also good, especially suitable for the family network; the mouse used a few TP-LINK router, I feel good. Besides, Chinese people must also support Chinese goods. If you only want to set up a vro, you only need to select the setting wizard and configure the network according to your Internet access mode to implement the routing function. For the Internet access method, please select according to your own situation. Here, we use the most common domestic ADSL virtual dial-up PPPoE dialing method as an example.

Select ADSL virtual dialing PPPoE), click Next, and enter your account name and password. If you do not know, please contact your local IP service provider. Click Next to enter the Wireless Settings interface, the TP-LINK is wireless by default open, because we this article mainly introduces Wireless Settings, so if the wireless function of this setting interface is not open, choose to open, click Next to complete vro settings. Because the IP address of the wireless router is set, the router will be re-connected. If the router is started correctly, select the running status on the interface to display the current status of the router correctly. If the WAN port status is set, an error is displayed. Set the error for you. Set it again.

After the IP address of the wireless router is correctly connected, if you want the following clients to conveniently configure the network, you can enable the DHCP service in the vro, the TCP/IP protocol for all computers in the LAN connected to the router is set to "automatically obtain the IP address", and the router can automatically configure the network for each machine. In this way, you do not need to specify IP addresses for each machine. Of course, you can also manually specify IP addresses for each computer when the DHCP service is enabled. 2. Set the wireless network card. First, install the driver of the wireless network card correctly. Then, select control panel-network connection-select wireless network connection and right-click and select Properties.

Select Configuration in the connection attribute of the wireless network adapter, select the AD Hoc channel in the attribute, and select 6 in the value. The value should be consistent with the value of the radio frequency band set by the wireless router IP address, and click OK. In general, the frequency band of the wireless network card does not need to be set, and the system will automatically search. The wireless network card of the mouse can automatically find the frequency band. Therefore, if you set a wireless route, the wireless network card cannot find the wireless network, which is usually the reason for the frequency band setting, follow the correct frequency band above. After setting the surface, select Control Panel> network connection> double-click wireless network connection and select the wireless network connection status. In the correct case, the wireless network should be connected normally.

If no connection is displayed in the wireless network connection status, click View wireless network, refresh the Network List, and click Connect after the system detects the available wireless network, you can complete the wireless network connection. In fact, wireless network settings are basically the same as those for wired websites. The preceding settings can only be completed if you only set up a wireless network. The above article only introduces the connection between a computer and a wireless router. If multiple machines are connected, it is the same as the single-host setting. Because the DHCP service is set in the vro, you cannot specify an IP address to complete the network configuration of multiple machines. If you want to manually specify the IP address of each machine, you only need to specify the IP address in the NIC TCP/IP Settings. However, you must note that the IP address must be set in the same CIDR block as the vro, set the gateway and DNS to the IP address of the wireless router.