--------------Router basic configuration of routing switching

System Bootstrap, Version 12.1 (3r) T2, RELEASE Software (FC1)

Copyright (c) by Cisco Systems, Inc.

Cisco 2811 (MPC860) Processor (revision 0x200) with 60416k/5120k bytes of memory

Self decompressing the Image:

########################################################################## [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

Subject to restrictions as set forth in subparagraph

(c) of the commercial computer software-restricted

Rights clause at far sec. 52.227-19 and subparagraph

(c) (1) (ii) of the rights in Technical Data and computer

Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.

West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, 2800 software (c2800nm-advipservicesk9-m), Version 12.4 (all T1), RELEASE Software (FC2)

Technical Support:http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 18-jul-07 06:21 by Pt_rel_team

Image text-base:0x400a925c, Data-base:0x4372ce20

This product contains cryptographic features and was subject to

States and local country laws governing import, export, transfer and

Use. Delivery of Cisco cryptographic products does not imply

Third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users is responsible for

Compliance with U.S. and local country laws. By using the This product

Agree to comply with applicable laws and regulations. If you are unable

To comply with U.S. and local laws, return this product immediately.

A Summary of U.S. laws governing Cisco cryptographic products is found at:

Http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance, contact us by sending email to

[Email protected]

Cisco 2811 (MPC860) Processor (revision 0x200) with 60416k/5120k bytes of memory

Processor Board ID Jad05190mtz (4292891495)

M860 processor:part number 0, mask 49

2 Fastethernet/ieee 802.3 interface (s)

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (read/write)

Cisco IOS Software, 2800 software (c2800nm-advipservicesk9-m), Version 12.4 (all T1), RELEASE Software (FC2)

Technical Support:http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 18-jul-07 06:21 by Pt_rel_team

---System Configuration Dialog---

Continue with Configuration dialog? [yes/no]: Y

At any point, you may enter a question mark '?

Use Ctrl-c to abort the configuration dialog at any prompt.

Default settings is in square brackets ' [] '.

Basic management setup configures only enough connectivity

For management of the system, extended setup would ask you

To configure all interface on the system

Would to enter basic management setup? [yes/no]:?

% please answer ' yes ' or ' no '.

Would to enter basic management setup? [Yes/no]: N

First, would you like to see the current interface summary? [Yes]:y

Current Interface Summary

Interface ip-address OK? Method Status Protocol

fastethernet0/0 Unassigned YES Manual administratively down

FASTETHERNET0/1 Unassigned YES Manual administratively down

Vlan1 Unassigned YES Manual administratively down

Configuring Global Parameters:

Enter host name [Router]: FWC01

The Enable secret is a password used to protect access to

Privileged EXEC and configuration modes. This password, after

Entered, becomes encrypted in the configuration.

Enter Enable Secret:521xxn

The Enable password is used if you don't specify an

Enable secret password, with some older software versions, and

Some boot images.

Enter Enable password:123456

The virtual terminal password is used to protect

Access to the router over a network interface.

Enter Virtual Terminal password:111111

Configure SNMP Network Management? [No]:n

Configuring Interface Parameters:

Do you want to configure Vlan1 interface? [No]:y

IP address for this interface:192.168.1.100

Subnet mask for this interface [255.255.255.0]:

Do you want to configure fastethernet0/0 interface? [no]:192.168.1.110

% please answer ' yes ' or ' no '.

Do you want to configure fastethernet0/0 interface? [No]:yes

IP address for this interface:192.168.1.110

Subnet mask for this interface [255.255.255.0]:

Do you want to configure FASTETHERNET0/1 interface? [No]:y

IP address for this interface:192.168.1.120

Subnet mask for this interface [255.255.255.0]:

The following configuration command script was created:

!

Hostname FWC01

Enable Secret 5 $1$MERR$BGREVRMQDV0QPJF2ZVZKM1

Enable password 123456

Line vty 0 4

Password 111111

!

Interface Vlan1

No shutdown

IP address 192.168.1.100 255.255.255.0

!

Interface fastethernet0/0

No shutdown

IP address 192.168.1.110 255.255.255.0

!

Interface FASTETHERNET0/1

No shutdown

IP address 192.168.1.120 255.255.255.0

!

End

[0] Go to the IOS command prompt without saving this config.

[1] Return to the setup without saving this config.

[2] Save this configuration to NVRAM and exit.

Enter your selection [2]: 2

Building configuration ...

[OK]

This article is from the "Make a few" blog, be sure to keep this source http://9399369.blog.51cto.com/9389369/1731330

--------------Router basic configuration of routing switching