A cainiao talks about Router

TodaySorry, we asked ourselves a question: "What is the button behind the router used? "
OMG, thinking for half a day, then, "that button is used to restore factory settings"
It has always been a cainiao on the Internet.

In short, there is a plug-in on the wall, and you have a lot of power equipment, you need to buy a plug-in, and this plug-in is equivalent to a router
A vro allows a single network cable to allow multiple computers to access the Internet at the same time.
We generally use the ADSL modem (also known as "cat") to provide the router function.
However, a broadband cat can only use one computer to access the Internet.
The number of computers connected to the Internet is determined by the route port.
Turn it off when you don't need it, because some routers will automatically dial up to connect to the network when you don't access the internet.
When we saw a girl on TV, we were owed thousands of Internet fees.

The following experts will work with you on several "technical activities"

(I) hardware Installation

① When setting up a home network for the first time, disconnect the power of all devices, including hosts, monitors, modem, and routers.
② Connect the network cable to the network card of each computer in the LAN, while the other end of the network cable is connected to the lanport in the rear panel of the router
Tip: The TL-R410 router has a total of 4 ports for the client to use the computer in this LAN can be any access to these ports
There is no order requirement. In addition, there is an uplink port, which can be used in combination with each other. Do not insert this port.
③ Connect the residential broadband network cable to the WAN port behind the router
④ Connect the power port behind the router to the power supply

After all the hardware is installed and confirmed to be correct, connect to the power supply and start the computer

(Ii) configure a Broadband Router

The Broadband Router provides three Internet Configuration modes: static IP, dynamic IP, and pppoe.
If you are using residential broadband, select static IP and set the following parameters: IP address, gateway, and subnet mask. First, the DNS server and the backup DNS
If you are using ADSL, select pppoe and remember your username and password.

Enter http: // 192.168.1.1 in the address bar of the browser.
This address is the IP address of the Broadband Router.
However, different brands of broadband routers have different configurations. before configuring a vro, you must read the specification for this model.
The factory default information of the TL-R410 router is:
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Username/password: admin/admin

On the "Wan Port Settings" interface, you must first set the connection type for accessing the Internet, because we use residential broadband.
Click the drop-down menu of "Wan port connection type", select "static IP Address", and enter the corresponding user name and password in "Internet account" and "Internet password ".
Then, select the "use isp ip Address" and "manually set DNS server" check boxes, and enter the IP address and DNS address specified by the ISP.
After setting, click "save"

In "select the connection mode as needed :"
Here, we recommend that you select "automatic connection, automatic connection after startup and disconnection", that is, you can connect to the network at startup.

(Iii) Set DHCP Functions

Another special function of a router is to provide the DHCP service.
We do not need to manually assign IP addresses to each client to allow computers in the LAN to access each other.
If the DHCP service is disabled on the vrodhcp, you must set the IP address in the same network segment as the vro. Set the IP address of the vro as the IP address and enter the DNS server parameters.

(Iv) Internet sharing

Because the vrodhcp has a built-in DHCP server, we only need to open any computer and start the browser to access the Internet.

(V) How to easily bind a MAC address

In order to prevent Internet sharing by binding the MAC address of the NIC to some local terminals
The TL-R410 router also designed a "MAC address clone" for us"
Enter the MAC address of the NIC connected to the original line, and click "clone MAC address"
Your MAC address is copied to achieve Internet sharing.