Classic Summary of Huawei H3C router configuration commands

It is useful to know about the Huawei H3C router configuration commands and make them easier to use. Many people may not understand the specific meanings of these commands, after reading this article, you must have gained a lot. Configure the terminal operation password for the Huawei H3C router configuration command:

[ST-ZC501-LSW-R4C14. I .S2403] user-interface aux 0/enter user 0 Mode
[ST-ZC501-LSW-R4C14. I .S2403-ui-aux0] authentication-mode password/configure password

No operation to automatically disconnect:

Idle-timeout minutes: no operation in 10/10 minutes, automatic disconnection
Idle-timeout seconds: no operation in 10/10 seconds, automatic disconnection

Locked users:

Lock/lock the current user (enter the password and press enter to unlock the password you just entered ).

Enable the telnet service:

[ST-ZC501-LSW-R4C14. I .S2403] telnet server enable/start telnet Service (disabled by default) Force user deprecation:
Free web-users all/force all online WEB users to go offline and view the number of received, transmitted, and dropped packets on the Port:
Display garp statistics interface (plus port number) Check the number of GVRP packets received, transmitted, and discarded by the port

VTP Configuration:

Gvrp registration fixed/port mode configuration (equivalent to Cisco's server mode VTP) ____ must be under the trunk working mode port.
Gvrp registration forbidden/port mode configuration (equivalent to Cisco's transparent mode VTP) ____ must be under the trunk working mode port.
Gvrp registration normal/port mode configuration (equivalent to Cisco's client mode VTP) ____ must be under the trunk working mode port.

View the device ID of the local system, including the LACP copriority and MAC address: display lacp system-id
Priority is set to 64 (smaller value greater priority): [ST-ZC501-LSW-R4C14. I .S2403] lacp system-priority 64
Port aggregation name: [ST-ZC501-LSW-R4C14. I .S2403] link-aggregation group 1 description
Name create a manual aggregation group with group number 8: [ST-ZC501-LSW-R4C14. I .S2403] link-aggregation group 8 mode manual
Add the port to the manual aggregation group with group number 8: port link-aggregation group 8 under the port
Go to aggregation port group 8 Mode: [ST-ZC501-LSW-R4C14. I .S2403] port-group aggregation 8

Bind the IP address and MAC address under the Port: user-bind ip-address 121.11.86.72 mac-address 0101-0101-0101
View abnormal blocked port: display stp abnormal-port shows the result as Formatcompatibility rotected in the Reason item
View the port information of the STP protection function down: display stp down-port
View the root bridge information of all MSTP instances: dis stp root
Clear the statistical information of the Spanning Tree: reset stp interface port number ------ eliminate the statistical information of the Spanning Tree of the specified port.
Display stp region-configuration
Enable and disable STPS: [ST-ZC501-LSW-R4C14. I .S2403] STPS enable global STPS
Disable stp: stp disable under the Port
The path overhead of the configured port under the Port): stp instance 0 cost 16 ______ specifies that the path overhead of the Spanning Tree instance 0 is 16
Specify the root bridge of the Current Device for Spanning Tree instance 0: stp instance 0 root primary

Backup root bridge for the current device generation tree instance 0: stp instance 0 root secondary
Port root protection: stp root-protection
Configure the Ethernet port as the edge port, that is, the direct forwarding port -- no blocking port): stp edged-port disable
Enable loop protection under the Port: stp loop-protection

Route command:

Display ip routing-table
View the abstract information of an active route filtered by ACL2000 in the basic access control list: display ip routing-table acl 2000.
View the details of active and inactive routes filtered by the basic access control list ACL2000: display ip routing-table acl 2000 verbose

These Huawei H3C router configuration commands are common. I hope you will have a better understanding of these configuration statements after reading the article, and avoid problems during the routing process.