Common Internet cafe mouse faults and Solutions

USB mouse
Symptom 1: The mouse cannot be used under DOS and Win 95.
Method: Upgrade Windows 95.
Step: directly execute D: SETUP in start, program, and run under Win 95 assuming D is a CD drive) to upgrade Win 95B or Win 98. Note: DOS does not support USB interfaces, whereas only Windows 954.00.950B in Win 95 supports USB interfaces. Of course, Windows 98 also supports USB interfaces. To detect Windows 95, open control panel and system. For details, see version information on the first page of the dialog box.
Symptom 2: The new USB mouse, unplug the original PS/2 mouse, insert the mouse, enter the Windows 98 desktop, the system reports an error, said the mouse could not be detected.
Method: if you do not pull the original mouse, insert the mouse to start the system.
Step: after shutdown, insert the original mouse. After the boot, the system will find the new hardware. Use the original mouse to insert the system disk and install the USB mouse as prompted by Win 98. After the installation is successful, you can shut down the server.

You can only use the mouse for a moment.
Symptom: My computer was used normally. Recently, some devices were added to the office. After the installation was completed, the mouse was started after Windows 98 was started, then the serial mouse cannot be used, and the keyboard can be used at this time.
Method: view the Device Manager to solve the interruption conflict.
Step: Use a PS/2 mouse to change the serial mouse. Right-click my computer and select "Device Manager" to check whether there is a yellow symbol before "Mouse" or other options. Once such a device is found, change its interruption to another value to avoid interruption 3 or 4. Under normal circumstances, Serial 1 is interrupted 4, Serial 2 is interrupted 3. You can also directly view the interrupt usage to see which device is interrupted 3 or 4.
Note: This is a typical scenario where mouse interruptions conflict with other devices. You can also use the mouse of another interface. For example, if you use the serial mouse to see the fault, you can use the PS/2 mouse. If you use the PS/2 mouse to see the fault, you can replace the serial mouse. Note that the PS/2 mouse is interrupted by 12.

No mouse detected in Windows 9x
Symptom 1: After a new computer is started in another place, the system prompts that the mouse cannot be detected and the keyboard does not respond.
Method: Replace the keyboard and mouse interfaces.
Step: After the instance is shut down, unplug the mouse and keyboard from the back of the chassis, swap the mouse and insert it back.
Note: On the new computer, the interface between the mouse and the keyboard is the same. After the place is changed, the interface must be reversed, so the mouse and the keyboard cannot be used. The updated motherboard mouse and keyboard interface have obvious differences in color and icon.
Symptom 2: The mouse was used for a long time and suddenly could not be detected. You can use it by inserting another mouse on my computer. You can also use it by inserting the mouse on another computer, but your mouse cannot be used on your computer. I am using an A4 brand mouse with a serial port.
Method: Switch the mouse with another user, or change the serial port or serial port.
Step: Change the mouse
Note: The interface is easy to loosen when there are too many mouse plug-ins. In this case, the interface requires a tight mouse. Therefore, you can change to a new one. Although other mouse can be used on your computer, it only means that the interface of that mouse is relatively tight. If the above method does not work, try plating a layer of TiN on the mouse pin. The new mouse price is also very cheap. You may wish to purchase a new one.
Symptom 3: The old Intel optimized HX meijie motherboard was not fully packaged, and the serial port and parallel port were not connected. I found some lines and couldn't detect the mouse. Is there a problem with the main board serial port or the connection line does not match. I have checked the BIOS settings to ensure that there is no problem. The mouse has changed a few times, and none of them can be detected.
Method: Ask the dealer for a connection to the motherboard.
Note: although both the serial port and the parallel port are standard, some serial ports on the main board cannot be used in general. You must use the line with the original motherboard.
Symptom 4: The newly purchased A4 single swallow PS/2 mouse, with a PS/2 interface switching serial port converter. If the converter is not used, it is normal, but the mouse does not
Method: The difference is the computer PS/2 interface fault or the converter fault.
Step: Use a PS/2 mouse. If the above fault does not occur, it indicates that the converter is faulty; otherwise, the PS/2 interface of the motherboard is faulty.
Note: You must promptly discover problems and get an early warranty.
Symptom 5: The computer I just assembled can use the serial mouse. When the PS/2 mouse is used, the system cannot detect the mouse. This mouse can be used on other computers. You cannot use another PS/2 mouse.
Method: Set PS/2 in SETUP to "Enabled ".
Step: Press DEL to enter the motherboard SETUP, enter "integrated peripherals", and set "PS/2 MOUSE" to "Enabled ".
Note: The PS/2 mouse is different from the serial mouse. The former may require the settings in the motherboard SETUP, while the latter does not need to be set. Note: Some motherboard bios setup only has "PS/2 Mouse Power On", and it has nothing to do with this fault.
Symptom 6: The mouse that can be used normally is broken after the child plays in front of the computer for a while. I am using Win 95. No mouse detected at startup. The driver in DOS cannot work with the mouse.
Method: Check the switch at the bottom of the mouse.
Step: The switch is mostly at the bottom or side of the mouse.
Note: There is a switch between two keys and three keys at the bottom of some mouse nodes. Please switch to the other side. It is estimated that the child has moved it. Usually 2 MS) or 3 PC at the switch ). Windows 95 can directly detect the MS mode. If you use the PC mode, you need to set Windows 95 SYSTEM. the MOUSE in the BOOT segment of the INI file. DRV = LMOUSE. change DRV to MOUSE. DRV = MSCMOUSE. DRV.

Bad mouse button
Symptom: the left mouse button does not work recently. You can also right-click it. Because my location is remote, is there any way to temporarily use it for a while?
Method: Set the left hand habits.
Step: select "my computer", "Control Panel", "Mouse", "button", "Left Hand habits", and "OK.
Note: in this way, you can right-click.

Mouse with tail
Symptom: When I came back from a business trip, I found that my computer's mouse was abnormal. Every time I move it, I had a tail. It was made up of some mouse pointers. Is the mouse broken?
Method: Set the mouse property.
Step: select "my computer", "Control Panel", "Mouse", "attribute", and "show pointer track". After X disappears before this option, select "OK ".
Note: It is only a normal display mode of the mouse. You can change it to the normal mode.
Symptom: A computer uses a graphics card of SIS 6326 and sets the mouse as a 3D pointer. After playing a card for about half an hour, the mouse pointer is dragged to the end, mouse prints are left on the place where the pointer is moved, and the whole screen is gradually spent.
Method: Upgrade the driver of the display card.
Step: omitted.
Note: In this example, the video card driver of SIS 6326 is updated from V1.09 to V1.21 to solve the above problem. NOTE: If there is no better driver at the time, you can only wait for the new driver to appear.

Insufficient serial port
Symptom: The mouse and MODEM are already on the serial port. Now I want to use a serial-port plotter. What should I do?
Method: Use the PS/2 mouse or built-in MODEM or USB mouse.
Step: USB mouse driver does not need to be followed by the mouse. It can also be hot-swappable and can be installed and disassembled without shutdown. After the USB mouse is inserted into the flat USB interface of the computer, Win 97/98 will automatically detect the device. Follow the prompts to insert the system installation disk.
Note: After you change the cursor to PS/2, a serial port is provided for the plotter. If there is no PS/2 interface on the computer, you can only change the built-in MODEM. However, it is difficult to set up. You cannot use interrupt 3 or 4, and the addresses cannot conflict with them. USB mouse does not occupy the COM interface. Most 586 computers, all 686 computers support USB mouse. However, the USB port attachment is required for the 586 PC. Windows 95 does not support USB interfaces.

Related Articles]

• Summary of classic faults in Internet cafes (I)
  

• Solution to instant disconnection in Internet cafes
  

• Classic Fault Analysis for Internet cafes