Love fast Soft routing +panabit Internet Behavior management

Love fast Soft routing +panabit Internet Behavior management

Preparatory work:

Hardware Device: One 1U Lenovo Thinkserver RS140//Install love fast soft route

The other is the assembly machine configuration as follows//install Panabit behavior monitoring software
Motherboard: Gigabyte GA-H81M-DS2
Processor: Inter G3220 (Chinese original box pack)
Memory: Kingston DDR3 4G 1600
HDD: Seagate SATA 500GB
Chassis: Jinhe field 8512, 8519 (without power)
Power: Air ka cool King Diamond version 2.31
Network card: Tp-link tg-3269c Gigabit PCI NIC 3//three gigabit NICs one WAN, one LAN and one Management port.

Network devices:

Two layer switch tri (H3C) S5120-28p-li core Ethernet switch//partition good vlan10,vlan20,vlan30 ... 23, 24 port for trunk port, VLAN connected to the idiot switch or s1526 network management line can also.

1. First download love fast ISO software, use the old Peaches start custom ISO To install the free version love fast soft routing//Love fast Soft routing default username and password are admin

http://www.ikuai8.com/

2. Download panabit Internet Behavior management software//Use the old peaches to start the custom ISO to install the free version of the Panabit software

Http://www.panabit.com/html/product/std/2014/0725/30.html

3. Use the console port to plan ports and VLANs, and the last 23 and 24 port are trunk ports

VLAN10//Create Vlan10

Port Ethernet 1/0/1 to Ethernet 1/0/10//vlan10 1-10 ports

vlan20//Creating Vlan20
Port Ethernet 1/0/11 to Ethernet 1/0/21//vlan11 1-21 ports

Interface Ethernet 1/0/23//Enter port mode
Port Link-type trunk//Set ports operating mode trunk
Port Trunk Permit VLAN all//Set trunk allows all VLANs via LAN port for fast soft routing of Love

And so on

4. Connect the physical line in and out, in the Love fast router set vlan10,vlan20,vlan30.......,dhcp settings 192.168.10.100-192.168.10.200 ..., the default VLAN can be communicated between the Just do the ACL on the love fast router to isolate

5. We want to configure Panabit for bridge mode. Bridge is the corresponding, not one is the bridge 1, the other is Bridge 2, must correspond to a WAN LAN, and finally update the system http://forum.panabit.com/forum-13-1.html
Server Panabit 9.2 Version user name is root, password: Panaos, Web Management for HTTPS://IP user name: admin password: panabit

Tips for writing strategies.
1) Apply the classification, the similar application to the custom protocol group, such as Thunder, Qvod and so on. Some applications that continue to download can be grouped into a custom protocol group.
2) IP classification, the establishment of different IP groups, different groups to do different strategies.
3) The sequence number of the strategy is not continuous, the interval magnified some, convenient to insert other strategies.
4) The upstream and downstream strategies are separated.
5) When dynamic speed limit is enabled, the line default bandwidth should be populated with the bandwidth value that the line actually can achieve.
6) The channel size should not be greater than the actual bandwidth, should be slightly smaller than the actual bandwidth.
7) The key application does not put in the channel, although the channel has the priority, but the channel is also a limit.
8) through the uplink control downlink, the lower the upstream, the smaller the downward, this everyone can test themselves.

This article is from the "a Willing heart!" blog, be sure to keep this source http://zh888.blog.51cto.com/1684752/1599187

Love fast Soft routing +panabit Internet Behavior management