#!/bin/bash #密碼變數
password="" #安裝texlive
installTex(){
if [ "$1" = "1" ]; then
echo "==>texlive簡單安裝..."
sudo -K
echo $password| sudo -S apt-get -y install texlive texlive-math-extra texlive-latex-base texlive-latex-extra texlive-latex-recommended texlive-pictures texlive-science texlive-bibtex-extra texlive-common latex-beamer
elif [ "$1" = "2" ]; then
echo "==>texlive完整安裝..."
sudo -K
echo $password| sudo -S apt-get -y install texlive-full latex-beamer
else
echo "==>不安裝texlive"
fi
} #安裝CJK
installCJK(){
if [ "$1" = "1" ]; then
echo "==>CJK中文支援..."
sudo -K
echo $password| sudo -S apt-get -y install latex-cjk-chinese ttf-arphic-* hbf-*
elif [ "$1" = "2" ]; then
echo "==>CJK完全支援..."
sudo -K
echo $password| sudo -S apt-get -y install latex-cjk-all
else
echo "==>不安裝CJK"
fi
} #安裝fontforge
installFontforge(){
if [ "$1" = "1" ]; then
sudo -K
echo $password| sudo -S apt-get -y install fontforge
else
echo "==>不安裝fontforge"
fi
} #進度列表
stepEcho(){
case "$1" in
1) echo "安裝Texlive和一些常用宏包配置";;
2) echo "安裝CJK包配置";;
3) echo "安裝fontforge配置";;
4) echo "確認subfonts.pe和Unicode.sfd檔案路徑";;
5) echo "設定CJK字型引用名";;
6) echo "正式安裝texlive";;
7) echo "正式安裝CJK";;
8) echo "正式安裝fontforge";;
9) echo "正式檢查subfonts.pe和Unicode.sfd存在性";;
*) echo "迴圈處理字型中...";;
esac
} #產生map檔案
makemap(){
for i in *.tfm
do
echo "${i%.tfm} ${i%.tfm} < ${i%.tfm}.pfb" >>$1
done
} #檢測傳回值錯誤提示，和$?配合
perr(){
if [ "$1" != "0" ]; then
echo "[錯誤！]錯誤碼="$1
fi
} ################main################
proc="0" #進度參數
procFile="./texsetup.sh_procFile" #進度記錄檔案
maprec="./texsetup.sh_maprec" #記錄產生的map列表
subfontsPath="/usr/share/latex-cjk-common/utils/subfonts/subfonts.pe" #subfonts.pe檔案的預設位置
UnicodePath="/usr/share/texmf/fonts/sfd/Unicode.sfd" #Unicode.sfd檔案的預設位置
findpath="/usr" #如果上面兩個檔案找不到，預設到這個目錄下找
#CJK路徑
mapPath="$HOME/.texmf-var/fonts/map/dvips/CJK/"
tfmPath="$HOME/.texmf-var/fonts/tfm/CJK/" #+"citename"
typePath="$HOME/.texmf-var/fonts/type1/CJK/" #+"citename"
encPath="$HOME/.texmf-var/tex/latex/CJK/" #+"encoding" #開始歡迎資訊
clear
echo "=============================================================="
echo "[[Texlive+Latex+CJK+字型配置]]"
echo "使用方法："
echo "將需要添加的字型檔都放到一個可寫的臨時目錄(比如~/tempfont)裡,然後將指令碼"
echo "檔案也放到該目錄下,運行即可,注意不要用root許可權運行本指令碼！！！"
echo "==============================================================" usernow=`whoami`
if [ "$usernow" = "root" ]; then
echo "不能用root許可權運行本指令碼！"
exit 1
fi
echo "現在才需要輸入sudo密碼～"
echo -n "password:"
stty -echo
read password
stty echo
echo "輸入完畢"
sudo -K
echo "檢測當前許可權..."
echo $password |sudo -S whoami
success=`echo $?`
if [ "$success" = "0" ];then
echo "密碼輸入正確"
else
echo "密碼輸入錯誤"
exit 1
fi
echo "==============================================================" echo "完成後是否刪掉臨時目錄（刪掉不影響字型使用）？"`pwd`
RMYES="1"
OPTIONS="刪掉 保留"
select opt in $OPTIONS;do
if [ "$opt" = "刪掉" ]; then
RMYES="1"
break
elif [ "$opt" = "保留" ]; then
RMYES="0"
break
else
echo "錯誤選擇！"
fi
done
echo "==========================================================" #檢測系統資訊
echo "系統資訊檢測"
echo "----------------------------------"
echo "系統資訊："`cat /proc/version`
sysinfo=`cat /proc/version |egrep -i "ubuntu|debian"`
if [ -z "$sysinfo" ]; then
echo "你的系統不是ubuntu/debian，某些步驟可能不能正常工作："
OPTIONS="繼續 退出"
select opt in $OPTIONS;do
if [ "$opt" = "繼續" ]; then
break
elif [ "$opt" = "退出" ]; then
exit 0
else
echo "錯誤選擇！"
fi
done
fi
encoding=`env |grep -i '^lang'`
encoding=${encoding##*.}
echo "編碼："$encoding
if [ "${encoding:0:3}" != "UTF" ] && [ "${encoding:0:3}" != "utf" ]; then
echo "您當前系統預設編碼不是UTF8，其他編碼未測試可能支援不好，是否繼續？"
OPTIONS="繼續 退出"
select opt in $OPTIONS;do
if [ "$opt" = "繼續" ]; then
break
elif [ "$opt" = "退出" ]; then
exit 0
else
echo "錯誤選擇！"
fi
done
else
encoding="UTF8"
fi
echo "==========================================================" #0:查看進度記錄是否存在
echo "查看是否存在進度記錄"
echo "<注意重啟或登出可能會導致記錄消失>"
echo "----------------------------------"
if [ -e "$procFile" ];then
proc=`cat $procFile`
echo -n "存在進度記錄"$proc"=>"
stepEcho $proc
OPTIONS="從進度記錄處開始 從頭開始"
select opt in $OPTIONS;do
if [ "$opt" = "從進度記錄處開始" ]; then
echo "正準備從進度記錄處開始..."
break
elif [ "$opt" = "從頭開始" ]; then
echo "正準備從頭開始..."
proc="1"
break
else
echo "錯誤選擇！"
fi
done
else
echo "無進度記錄，從頭開始..."
proc="1"
fi
echo "==========================================================" #1:安裝Texlive和一些常用宏包配置
if [ "$proc" = "1" ]; then
echo "安裝Texlive和一些常用宏包"
echo "<具體配置請閱讀指令碼installTex函數>"
echo "----------------------------------"
OPTIONS="簡單安裝 完整安裝 跳過本步"
select opt in $OPTIONS;do
if [ "$opt" = "簡單安裝" ]; then
s1="1"
break
elif [ "$opt" = "完整安裝" ]; then
s1="2"
break
elif [ "$opt" = "跳過本步" ]; then
s1="0"
break
else
echo "錯誤選擇！"
fi
done
proc="2"
echo $proc > $procFile
echo "=========================================================="
fi #2:安裝CJK包配置
if [ "$proc" = "2" ]; then
echo "安裝CJK包"
echo "<簡單安裝=中文支援>"
echo "<完整安裝=中日韓文等支援>"
echo "----------------------------------"
OPTIONS="簡單安裝 完整安裝 跳過本步"
select opt in $OPTIONS;do
if [ "$opt" = "簡單安裝" ]; then
s2="1"
break
elif [ "$opt" = "完整安裝" ]; then
s2="2"
break
elif [ "$opt" = "跳過本步" ]; then
s2="0"
break
else
echo "錯誤選擇！"
fi
done
proc="3"
echo $proc > $procFile
echo "=========================================================="
fi #3:安裝fontforge配置
if [ "$proc" = "3" ]; then
echo "安裝fontforge"
echo "<產生字型用，請務必安裝>"
echo "----------------------------------"
OPTIONS="安裝 跳過本步"
select opt in $OPTIONS;do
if [ "$opt" = "安裝" ]; then
s3="1"
break
elif [ "$opt" = "跳過本步" ]; then
s3="0"
break
else
echo "錯誤選擇！"
fi
done
proc="4"
echo $proc > $procFile
echo "=========================================================="
fi #4:確認subfonts.pe和Unicode.sfd檔案路徑
if [ "$proc" = "4" ]; then
echo "確認subfonts.pe和Unicode.sfd檔案位置"
echo "<fontforge產生字型用，務必確認正確，否則未必能自動找到>"
echo "-------------------------------------------------"
echo "subfonts.pe預設路徑="$subfontsPath
echo "Unicode.sfd預設路徑="$UnicodePath
OPTIONS="更改 不更改"
select opt in $OPTIONS;do
if [ "$opt" = "更改" ]; then
echo -n "subfonts.pe路徑[直接斷行符號採用預設]="
read filepath
if [ ! -z "$filepath" ];then
subfontsPath="$filepath"
fi
echo -n "Unicode.sfd路徑[直接斷行符號採用預設]="
read filepath
if [ ! -z "$filepath" ];then
UnicodePath="$filepath"
fi
echo "確認路徑分別為："
echo "subfonts.pe路徑="$subfontsPath
echo "Unicode.sfd路徑="$UnicodePath
break
elif [ "$opt" = "不更改" ]; then
break
else
echo "錯誤選擇！"
fi
done
echo -n "若以上路徑都不可用時，到$findpath搜尋[直接斷行符號採用預設]="
read tmpfindpath
if [ ! -z "$tmpfindpath" ];then
findpath="$tempfindpath"
fi
proc="5"
echo $proc > $procFile
echo "=========================================================="
fi #5:設定CJK字型引用名
if [ "$proc" = "5" ]; then
echo "設定字型引用名"
echo "說明：比如設定simsun.ttc的引用名叫song，在tex檔案中就是這麼引用\begin{CJK*}{GBK}{song}"
echo "--------------------------------------"
echo "<目錄中存在的檔案清單>"
ls
echo "分別設定引用名(注意不要出現重名)："
fontcount="1"
for i in *.ttc *.ttf *.bdf *.dfont *.bin *.hqx *.otf *.sfd *.pfa *.pfb *.cid *.ps *.svg *.pk *.pcf
do
if [ "${i:0:1}" = "*" ]; then
continue;
fi
echo -n "字型檔"$i"="
read fname
mv $i $fontcount"-RENAMEDFONT-"$fname"."${i##*.}
let "fontcount=$fontcount+1"
done
proc="6"
echo $proc > $procFile
echo "=========================================================="
fi #>=6:正式安裝中!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
echo "配置完成，進行正式安裝..."
echo "安裝過程將持續很長時間，處理一個字型大約花費幾十分鐘，請確認以上步驟均沒有錯誤，如果有錯誤請先結束指令碼再次運行，確認繼續？"
echo "選擇後請耐心等待結束，沒選項了= =|||......"
OPTIONS="繼續 退出"
select opt in $OPTIONS;do
if [ "$opt" = "繼續" ]; then
break
elif [ "$opt" = "退出" ]; then
exit 0
else
echo "錯誤選擇！"
fi
done #6:正式安裝texlive
if [ "$proc" = "6" ]; then
echo "★正式安裝texlive"
installTex $s1
perr $?
proc="7"
echo $proc > $procFile
fi
#7:正式安裝CJK
if [ "$proc" = "7" ]; then
echo "★正式安裝CJK"
installCJK $s2
perr $?
proc="8"
echo $proc > $procFile
fi
#8:正式安裝fontforge（若有必要，要順便配置PATH）
if [ "$proc" = "8" ]; then
echo "★正式安裝fontforge"
installFontforge $s3
perr $?
proc="9"
echo $proc > $procFile
fi
#9:正式檢查subfonts.pe和Unicode.sfd存在性
if [ "$proc" = "9" ]; then
echo "★檢查subfonts.pe和Unicode.sfd存在性"
if [ -e "$subfontsPath" ]; then
echo "subfonts.pe在預設路徑中找到"
else
echo "subfonts.pe沒找到在"$findpath"中尋找..."
subfontsPath=`find $findpath |grep -i "subfonts\.pe"`
if [ -z "$subfontsPath" ]; then
echo "[致命錯誤]沒找到subfonts.pe"
exit 1
else
echo "找到檔案："$subfontsPath
fi
fi
if [ -e "$UnicodePath" ]; then
echo "Unicode.sfd在預設路徑中找到"
else
echo "Unicode.sfd沒找到在"$findpath"中尋找..."
UnicodePath=`find $findpath |grep -i "unicode\.sfd"`
if [ -z "$subfontsPath" ]; then
echo "[致命錯誤]沒找到Unicode.sfd"
exit 1
else
echo "找到檔案："$UnicodePath
fi
fi
proc="10"
echo $proc > $procFile
fi #>=10:迴圈處理字型中
nowproc="9"
echo "★漫長的迴圈開始啦～～～～～～～～～～～～～～～～～～～～～～～～～～～～～"
#首先構造必要目錄
mkdir -p $mapPath
mkdir -p $encPath"$encoding"
echo "產生路徑："$mapPath
echo "產生路徑：${encPath}${encoding}" for fontfile in *RENAMEDFONT*
do
fonttype=${fontfile##*.}
tmpname=${fontfile##*-}
citename=${tmpname%%.*}
count=${fontfile%%-*}
let "nowproc=${nowproc}+1"
echo "☆當前處理字型為${citename}......"
if [ "$proc" -gt "$nowproc" ]; then
echo "==>已處理"
continue;
fi #如果提示找不到fontforge，看安裝成功沒，然後再檢查PATH
mapfilename=${citename}".map"
if [ ! -e "$mapfilename" ]; then
fontforge -script "$subfontsPath" "$fontfile" "$citename" "$UnicodePath"
fi
makemap $mapfilename
mkdir -p $tfmPath"$citename"
mkdir -p $typePath"$citename"
echo "產生字型路徑："$tfmPath"$citename"
echo "產生字型路徑："$typePath"$citename"
cp $citename".map" $mapPath
mv *.tfm $tfmPath"$citename"
mv *.pfb $typePath"$citename"
#產生fd檔案
echo "\ProvidesFile{c70${citename}.fd}" >>$encPath"$encoding/c70${citename}.fd"
echo "\DeclareFontFamily{C70}{${citename}}{\hyphenchar \font\m@ne}" >>$encPath"$encoding/c70${citename}.fd"
echo "\DeclareFontShape{C70}{${citename}}{m}{n}{<-> CJK * ${citename}}{}" >>$encPath"$encoding/c70${citename}.fd"
echo "\DeclareFontShape{C70}{${citename}}{bx}{n}{<-> CJKb * ${citename}}{\CJKbold}" >>$encPath"$encoding/c70${citename}.fd"
echo "\endinput" >>$encPath"$encoding/c70${citename}.fd" #記錄產生的map檔案名稱
echo $mapfilename >> $maprec let "proc=$proc+1"
echo $proc > $procFile
done #這個需要root許可權
sudo -K
echo $password| sudo -S texhash
#更新
for i in `cat $maprec`
do
updmap --enable Map $i
done #清理本臨時目錄
if [ "$RMYES" = "1" ]; then
rm -r `pwd`
fi echo "任務終了＝ ＝|||久等了......" |
