MD5 Checksums for R12.1.1 Rapid Install Media (文檔 ID 802195.1)

標籤：dir   md5sum   click   not   was   struct   rac   ber   pac   

Oracle EBusiness Suite R12.1.x Rapid Install
md5 Checksums November 2011

• Section      1: Overview     
• Section      2: Download md5 checksum results from Oracle
• Section      3: Compare md5 checksums
• Section      4: Disk overview, to be used when corrupted files are found

Section 1: Overview

After staging the Rapid Install software with the adautostg.pl script or downloading the Rapid Install software from Oracle Electronic Delivery, the md5 checksums for the staged directory structure can be used to validate the software integrity. Do this by running the md5sum program against the stage area using the oracle created checksum file. This is not an official development document - this procedure was performed/tested using the downloadable Rapidwiz media.

 Section 2: Download md5 checksum results from Oracle

Download the md5 checksum results from Oracle as posted below into a local file, for example <your platform> md5sum_.txt.

The attached files contain the md5 checksum results for every R12.1.1 release. Download the file corresponding to the used release and platform. The md5 checksum has been created without the startCD as it is often being updated, the checksum for the startCD‘s can be tested separately.

Release 12.1.1 Checksums currently available:

• R12.1.1      - Windows
• R12.1.1      - IBM AIX
• R12.1.2      - Linux on IBM System z
• R12.1.1      - Linux 32-bit
• R12.1.1      - Linux 64-bit
• R12.1.1      - Solaris Sparc 64-Bit
• R12.1.1      - HP_UX
• R12.1.1      - HP_UX Itanium

Release 12.1.x StartCD Checksums:

• R12.1.1      startCD - Version 12.1.1.9
• R12.1.1      startCD - Version 12.1.1.10
• R12.1.1      startCD - Version 12.1.1.11
• R12.1.2      startCD (Linux on IBM System z only) - Version 12.1.1.12.ZLINUX
• R12.1.1      startCD - Version 12.1.1.13

 Section 3: Compare md5 checksums

Compare the Stage with the md5sums downloaded from Oracle (md5sum_.txt). There should not be any FAILED entry in the output. If a FAILED entrie was found, then the stage area was not created successfully. The stage have to be re-created for every component indicating differences (FAILED).

Note: The following example assumes the stage   exists in /u01 for Unix and Linux, or F:\ for Windows customers.

Execute the following example commands to check stage using the the md5 checksums

• On Unix/Linux:
• Install the md5sum       utility for your platform if md5sum is not present on your system. If       md5sum is not available from your OS Vendor for your OS version (for       example HP 11.0), download and install the coreutils package from gnu.org .
• $ cd /u01/StageR12
• $ md5sum --check md5sum_Linux32.txt >       md5sum_result.txt
• On Windows:
• MKS Toolkit or cygwin       needs to be installed to be able to use mdm5sum.
• F:\> cd StageR12
• F:\StageR12> md5sum --check       md5sum_Windows.txt > md5sum_result.txt

 

Note: The md5 checksum will validate the entire   stage area and may take 10 minutes or more depending on hardware resources   and system load.     When the md5sum command failed for all lines with error: ": FAILED open   or read" try to make it a unix file using: dos2unix <checksum   file> <checksum file>

 

Section 4: Disk overview, to be used when corrupted files are found

When a corrupted file is found the following can be used to identify which part needs to be re-downloaded from edelivery.

Release 12.1.1 Disk overview:

• R12.1.1      - Windows
• R12.1.1      - IBM AIX
• R12.1.2      - Linux on IBM System z
• R12.1.1      - Linux 32-bit
• R12.1.1      - Linux 64-bit
• R12.1.1      - Solaris Sparc 64-Bit
• R12.1.1      - HP_UX
• R12.1.1      - HP_UX Itanium

 

MD5 Checksums for R12.1.1 Rapid Install Media (文檔 ID 802195.1)