kernel 啟動後沒有eth0

       最近做視頻電話項目，用mx515 CPU，以前編譯的kernel啟動從來問題，

可進來發現，啟動之後ifconfig 發現沒有eth0,執行以下命令：

#ifconfig
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:280 (280.0 B)  TX bytes:280 (280.0 B)

# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:00:00:00:00:00 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Base address:0xc000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:5 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:455 (455.0 B)  TX bytes:455 (455.0 B)

 

 

很是鬱悶，回頭看看fec啟動log資訊，發現：

FEC ENET Version 0.2
fec: PHY @ 0x2, ID 0x0007c0f1 -- LAN8710
eth0: ethernet 00:00:00:00:00:00

原來是MAC地址為0所致，解決方案可以在kernel下用命令：

方法1:

# ifconfig eth0 hw ether 00:04:9f:00:ea:09

# ifconfig
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:21 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1855 (1.8 KiB)  TX bytes:1855 (1.8 KiB)

# ifconfig eth0 up

# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:04:9F:00:EA:09 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Base address:0xc000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:23 errors:0 dropped:0 overruns:0 frame:0
          TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2030 (1.9 KiB)  TX bytes:2030 (1.9 KiB)

#

已經可以了。

 

方法2:

在uboot啟動時設定mac 地址，下面是針對FEC的MAC地址，

 vdphone U-Boot > set fec_addr 00:04:9f:00:ea:09        
vdphone U-Boot > save