s5pc100開發板Nand flash移植

標籤：

相關軟體：http://pan.baidu.com/s/16yo8Y

fsc100開發板

交叉編譯工具：arm-cortex_a8-linux-gnueabi-gcc

 

?   添加針對我們平台的Nand flash驅動

拷貝s3c_nand.c到drivers/mtd/nand下

拷貝regs-nand.h到arch/arm/mach-s5pc100/include/mach下

?   針對平台上的nand flash裝置，修改drivers/mtd/nand/nand_base.c第2812行

for  (i = 0; i < 5; i++)

• 添加核心配置選項

修改drivers/mtd/nand/Kconfig，在if  mtd_nand下面添加如下內容：

 

config  MTD_NAND_S3C

        tristate "NAND Flash support for S3C SoC"

        depends on (ARCH_S3C64XX || ARCH_S5P64XX || ARCH_S5PC1XX || ARCH_S5PC100) && MTD_NAND

        help

          This enables the NAND flash controller on the S3C. 

          No board specfic support is done by this driver, each board

          must advertise a platform_device for the driver to attach.

 

config  MTD_NAND_S3C_DEBUG

        bool "S3C NAND driver debug"

        depends on MTD_NAND_S3C

        help

          Enable debugging of the S3C NAND driver

 

config  MTD_NAND_S3C_HWECC

        bool "S3C NAND Hardware ECC"

        depends on MTD_NAND_S3C

        help

          Enable the use of the S3C‘s internal ECC generator when

          using NAND. Early versions of the chip have had problems with

          incorrect ECC generation, and if using these, the default of

          software ECC is preferable.

 

          If you lay down a device with the hardware ECC, then you will

          currently not be able to switch to software, as there is no

          implementation for ECC method used by the S3C

 

修改drivers/mtd/nand/Makefile添加如下內容：

obj-$(CONFIG_MTD_NAND_S3C)  +=  s3c_nand.o

 

• 修改平台代碼

修改arch/arm/mach-s5pc100/mach-smdkc100.c添加如下內容：

 

• 添加標頭檔

#if defined (CONFIG_MTD_NAND_S3C)

#include <linux/mtd/partitions.h>

#include <linux/mtd/mtd.h>

#include <plat/nand.h>

#endif

 

• 添加平台裝置

#if defined(CONFIG_MTD_NAND_S3C)

/* Nand Flash Support */

static struct mtd_partition s5pc100_nand_part[] = {

        [0] = {

                .name        = "bootloader",

                .size        = SZ_1M,

                .offset        = 0,

        },

        [1] = {

                .name        = "kernel",

                .offset = MTDPART_OFS_APPEND,

                .size        = SZ_1M*3,

        },

        [2] = {

                .name        = "rootfs",

                .offset               = MTDPART_OFS_APPEND,

                .size        = SZ_4M,

        },

        [3] = {

                .name        = "usrfs",

                .offset        = MTDPART_OFS_APPEND,

                .size        = MTDPART_SIZ_FULL,

        },

};

 

struct s3c_nand_mtd_info s5pc100_nand_mtd_part_info = {

        .chip_nr = 1,

        .mtd_part_nr = ARRAY_SIZE(s5pc100_nand_part),

        .partition = s5pc100_nand_part,

};

 

static struct resource s5pc100_nand_resource[] = {

        [0] = {

                .start = 0xE7200000,

                .end   = 0xE7200000 + SZ_1M,

                .flags = IORESOURCE_MEM,

        }

};

 

struct platform_device s5pc100_device_nand = {

        .name                  = "s5pc100-nand",

        .id                  = -1,

        .num_resources          = ARRAY_SIZE(s5pc100_nand_resource),

        .resource          = s5pc100_nand_resource,

        .dev = {

                .platform_data = &s5pc100_nand_mtd_part_info,

        }

};

#endif

 

• 添加平台裝置列表

在smdkc100_device[]結構體數組中添加如下內容：

#if defined(CONFIG_MTD_NAND_S3C)

        &s5pc100_device_nand,

#endif

 

• 修改arch/arm/plat-samsung/include/plat/nand.h添加如下內容：

struct s3c_nand_mtd_info {

        uint chip_nr;

        uint mtd_part_nr;

        struct mtd_partition *partition;

};

 

• 配置核心

$ make menuconfig

Device Drivers  --->

        <*> Memory Technology Device (MTD) support  --->

               [*]   MTD partitioning support

<*>   Caching block device access to MTD devices

               <*>   NAND Device Support  --->

                      <*>   NAND Flash support for S3C SoC

                      [*]     S3C NAND Hardware ECC

 

File Systems  --->

         Partition  Types  --->

                [*]    Advanced partition selection

                [*]    PC  BIOS  (MSDOS  partition  tables)  support

                [*]         BSD  disklabel  (FreeBSD  partition  tables)  support

 

• 編譯核心並拷貝到tftpboot下

$ make  zImage

$ cp  arch/arm/boot/zImage  /tftpboot

 

• 測試

啟動目標板，在目標板上完成如下操作：

# cat  /proc/mtd

dev:        size       erasesize     name

mtd0: 00100000 00020000  "bootloader"

mtd1: 00300000 00020000  "kernel"

mtd2: 00400000 00020000  "rootfs"

mtd3: 0f800000 00020000  "usrfs"

 

s5pc100開發板Nand flash移植