VMware Network Adapter VMnet1和VMnet8 被歸入[未識別的網路-公用網路]的解決方案（轉錄的）

標籤：

系統: Windows7 x64

虛擬軟體: VMware Workstation 7.1.3

情況：VMware Network Adapter VMnet1和VMnet8 被防火牆認定為[未識別的網路-公用網路]，阻隔，無法使用連接埠映射，虛擬機器的80連接埠無法傳入，資料包只能出不能入。且公用網路被限制不能修改為家庭或工作網路。

解決方案：參考VMware的知識庫文章 [http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004813]

具體操作為以下這一段話：

Redefine the VMware virtual NICs as endpoint devicesThis procedure is permanent and allows for the continued use of Bridged, NAT, and Host Only networking. However, doing this causes the VMware virtual NICs to disappear from the Network and Sharing Center, even though they remain visible under Network Connections. This also causes the VMware virtual NICs to be exempt from all Windows Firewall access rules. When implemented, the control of virtual machine network access must be done from the guest operating system of each virtual machine. This bypasses the default security model of Windows with respect to the the VMware virtual NICs, and the implications of using this procedure must be carefully considered. To redefine the VMware virtual NICs as endpoint devices:

1. Click Start > Run, type regedit and, click OK.
2. Navigate to HKEY_LOCAL_MACHINE > System > CurrentControlSet > Control>Class > {4D36E972-E325-11CE-BFC1-08002BE10318}.
   
   Caution: VMware recommends that you back up this registry key before proceeding. To backup the registry:
   1. If {4D36E972-E325-11CE-BFC1-08002BE10318} is not still highlighted, click it.
   2. Go to File > Export.
   3. Pick a location and name for the Registration File (*.reg) .
   4. Click Save.
3. Click 0000.
4. Look at the content of the Data field associated with the DriverDescentry.
5. If you see VMware Virtual Ethernet Adapter for VMnet<x>, where<x> is replaced by a number, then:
   1. Right-click an empty space in the right content pane.
   2. Click New > Dword.
   3. Type *NdisDeviceType and press Enter.
      Note: Be sure to include the asterisk (*) at the beginning of the entry.
   4. Double-click *NdisDeviceType.
   5. Type 1 and press Enter.
6. Repeat steps 4-6, replacing 0000 in step 4 with the next entry in numerical order, until you have reached the end of all numerical entries.
7. Follow the Disable the VMware virtual NICs section of this article above.
8. Repeat step 8 but click Enable this network device instead.

 

簡單中文翻譯為：

1，進入註冊表[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}]，先匯出做備份。

2，逐項查看其下的[項]（0000，0001至00xx），看右邊哪一項的[值]為："DriverDesc"="VMware Virtual Ethernet Adapter for VMnet1"。

3，找到後，添加一個“DWORD”值（32位），名稱為“*NdisDeviceType”（*號是必須的），資料值改為“1”。

4，重複第2步，找 VMnet8 ，再重複第3步，添加值。

完成後重啟windows即可。

 

來源： <http://blog.sina.com.cn/s/blog_6452c6b40100qerm.html>　　部落格名字為：“ 永無止境的Pasu”

VMware Network Adapter VMnet1和VMnet8 被歸入[未識別的網路-公用網路]的解決方案（轉錄的）