Computer operation of the most taboo 18 little gestures

1, vigorously hit enter

This is probably a common problem for people, because the return key is usually when we finish one thing, the last to hit a button, presumably out of a triumph of excitement, everyone in the input of this enter key always so vigorously and readily tap. My keyboard is so scrapped, the first do not see the word is AWSD (hehe, heart know), the first key can not be used is enter.

Solution: There are two solutions, the first is to control your mood, and the second is to prepare your wallet. I choose the second, sometimes a good mood is money can not buy, you?

2, snack on the keyboard, drink

I am afraid this habit is very common, I see a lot of people are like this, especially fascinated by the computer table as a table to use. I think if you tear down your keyboard, perhaps the same behavior will be reduced, you can see your keyboard like Sui Ji, for your usual habits, retained a lot of "fossils", rice, biscuits, hair and so abound, no wonder someone said: The public room in the keyboard than the toilet is also dirty. At the same time, such fragments may enter your keyboard, blocking the circuitry on your keyboard, causing difficulty in typing. The damage to the drink is even more severe, and once is enough to destroy your keyboard. Is that your keyboard is lucky not to be destroyed, I am afraid to play the word, but also sticky very bad.

Solution: Avoid eating on the keyboard, or, like me, buy a waterproof Philips keyboard, and then give him clean every once in a while, sponge bath (although this is still very dirty); If you are more full, you can consider changing a keyboard for six months (I never recommend using a bad keyboard, That's a matter of health.) Try, it should be better. And remember to buy a table for your room.

3, CD-ROM is always placed in the CD-ROM drive (and watching VCD, after a pause after playing or eating)

Many people always like to put the CD-ROM in the CD-ROM, especially the CD, in fact, this habit is very bad. CD-ROM in the optical drive, the optical drive will be tested every once in a while, especially the burner, always in the continuous detection of optical drives, and high speed optical drive in the work, the motor and control parts will produce a very high heat, so the optical drive manufacturers have been trying to find solutions.

Although there are several ways to control the optical drive temperature within a reasonable range, but if the optical drive for a long time in the working state, then, even advanced technology can not effectively control the production of high temperature. Heat not only affects the stability of the parts, but also speeds up the wear of mechanical parts and the aging of the laser head. So it is unwise to make the optical drive work long hours, unless you want to cook your CD and CD-ROM.

Solution: Try to transfer the contents of the disc to the hard disk, such as converting the CD to MP3, if you are a perfectionist, then use the form of Virtual CD-ROM to manage your common CD-ROMs; The game uses the hard disk version as much as possible; Can be found on the Internet to convert the CD version to the hard disk version of the software, otherwise the same use of virtual CD-ROM format. There are many virtual optical drive can download, fear of trouble words can be made with the "Oriental Optical drive magician 3" or "VirtualDrive7.0", the interface is very simple, and no e-wen problem, very good to start.

4, off the machine and immediately reboot

Often someone shut down the machine to think of the CD did not take out, or there is something unfinished, etc., the author is one of them, you can say that there are many people with the same problem. A lot of people respond quickly, in the power off just finished can be remembered, and then put out a hand to boot, more DIY, always action sensitive, shutdown, 10 seconds to deal with the fault, reboot, no one knows how much harm to the computer.

First, the short time frequent pulse voltage shock, may damage the computer the integrated circuit; second, the most damage is the hard drive, now the hard drive is the high speed hard drive, from cutting off the power to the disc completely stop rotation, it takes a long time. If the disc does not stop, then reboot, it is equivalent to the deceleration in the state of the hard drive to accelerate. If you go on like this, the impact will surely make your hard drive die.

Solution: Shut down after something has forgotten to do, also put down his; must be completed, please wait more than a minute to reboot, or the machine does not disconnect the power when the chassis to press the hot boot key. If you can't do all the above, for the sake of your love machine health, I suggest you fasten a rope on the computer desk so that you can tie your hand for more than a minute.

5, the Boot box lid operation

Boot box lid to run a look at the things that are DIY are often done. It is true that the cover is open to make the CPU cooler, but at the expense of other accessories. Because the chassis cover is open, the convection is lost in the chassis, air flow will no longer go through the memory and other accessories, the most suffering is the front of the chassis of the optical drive and hard disk, loss of convection, will make their lower circuit board generated by the heat into the rise, not only scattered, but also used to heat themselves, especially the burner, The temperature will be much higher than usual.

Do not believe you compare the opening of the lid of the CD-ROM drive temperature. Boot box cover will also bring electromagnetic radiation, noise and other hazards, but also make the accessories in the chassis more easily dirty, bring electrostatic hazards, and hinder the rotation of the fan. At the same time, let other hidden dangers, such as you in front of the computer to watch a film, a hilarious lens so that you will be the mouth of the green tea into the Open box inside ...

Solution: Very simple, lock the lock on your cover and send me the key. If you are afraid of overclocking unstable, do not overclocking, now the CPU fast enough, in the market mainstream CPU is enough. If you are using the old CPU, I suggest you or change a good, change is hundreds of yuan or so (Celeron D or P4, AMD are also good) why suffer from the fear and electromagnetic radiation, noise pain? Or the phrase: Happiness is not bought by money.

6, touch the screen with the hand

In fact, either CRT or LCD can not be touched by hand. The computer will accumulate a large amount of electrostatic charge on the surface of the component during its use. The most typical is the display in the use of hands to touch the display screen, there will be severe electrostatic discharge phenomenon, electrostatic discharge may damage the display, especially the vulnerable LCD.

In addition, the surface of the CRT has strong light, anti-static Agas (anti-glareanti-static) coating, anti-reflective, anti-static Aras (anti-reflectionanti-static) coating, touch by hand, will also leave fingerprints on the top, Do not believe you look at the monitor from the side, you can see a fingerprint on your screen, do you want to help the Public security Bureau uncle's busy, in advance to extract the damage monitor "killer" fingerprint? At the same time, by hand touch the monitor, but also because the grease of the hand destroys the coating on the display surface.

LCD monitors are much more vulnerable than CRT monitors, pointing the finger at the LCD screen or poking at the screen is not advisable, although for CRT monitors this is not a big problem, but the LCD display is different, which may cause scratches on the protective layer, damage the display of liquid crystal molecules, so that the display effect of a large discount , so this bad habit has to be corrected, after all, your LCD monitor is not a touchscreen.

Solution: Put a fingerprint mark on your monitor, not to use your nails to paddle on the monitor, and to "round" on your screen, buy a laser-specific pen. Strong shock and vibration should be avoided, the screen and sensitive electrical components in the LCD display can cause damage if they are subjected to a strong impact; The display cleaning should be in a special video store to buy the appropriate cleaning agent, and then use the soft cloth such as glasses cloth gently scrub.

7. Always use the same wallpaper or screensaver with still screen

Whether CRT or LCD display, a long time to display the same screen, will make the corresponding area of aging faster, long this go on, will certainly appear distorted phenomenon. If you have a chance to look at the computer in the engine room, you will find that many of them already have a clear outline of the picture. What's more, life is colorful, why always use the same pair of faces?

Solution: Change a subject every once in a certain time, preferably not more than six months. You can turn off the monitor when you don't use it for a long time. If you don't have this habit, you can set the right time for the screen saver that displays the properties and let Windows help you with that.

8, put the CD or other things on the monitor.

The monitor becomes hot when it is running normally. To prevent overheating, the monitor sucks in the cold air, makes it pass through the internal circuit, and then drains it from the top. Do not believe you now touch the disc you put on it, is not hot like pancakes? If you always put the disc or paper on the monitor, it is more exaggerated to let your cat curl up in the winter, when the monitor is a hotbed, this will let the heat inside the monitor accumulation. Then color distortion, image problems, or even broken down will find your monitor.

Solution: If you want the display to retain the best quality and prolong its life, wake up your cat and let it sleep elsewhere. And get your "pancakes" in the CD bag.

9, take the computer host to the foot

If you want to kill your desktop computer, then take it to the cross-country drive, or carry it to climb the mountain, disco, it will be faster; Your method is too small and it takes a long time to get results. If you're willing to stick with it, the first thing you'll expect to achieve is a hard drive, the cause of the bad drive.

Solution: Take the picture of your tripod on your computer as your desktop, show you how ugly that pose is, so you don't get your feet to the mainframe again, or you stick your computer invoice on the monitor and look at the amount on the invoice, you shouldn't be indifferent. If none of the above methods can stop your behavior, I think you should consider buying a chair with irons.

10, computer and air-conditioning, television and other household appliances using the same power sockets

This is because the electrical appliances with the motor will produce spikes, surges and other common electrical pollution phenomenon, it will be possible to damage the computer's power system, so that your system can not operate or even damage. They also compete for power with the computer when they start up, and the consequence of a small reduction in electricity is that it may suddenly reboot or shut down your system.

Solution: For your computer not hungry or eat "food (power)" is not clean, first of all should use good quality computer switch power supply, such as the Great Wall and other brands. Second, for some users of the power environment is very unstable, it is recommended to buy UPS or voltage-stabilized power supplies such as equipment to ensure that the computer to provide clean electricity supply. There is the optimization of wiring, as far as possible to reduce the impact of various electrical appliances.

11, to your computer smoke second-hand smoke

Just as cigarettes, cigars, or tiny particles of smoke can hurt your lungs, smoke can run into your floppy drive and endanger data. Smoke may also overwrite the read head of the CD-ROM, DVD drive, causing a read error. Cigarette butts are more likely to make your printer and scanner quality drop dramatically.

Solution: The best way to protect your system and your own is not to smoke. If you just can't get rid of the habit of smoking, go out and smoke, or open the air freshener around the computer! Not to use your keyboard as an ashtray, of course.

After reading the hardware, let's take a look at the software issues.

12, keep changing the driver

A lot of DIY like the constant updating of the driver, although updating the driver may improve performance and compatibility, but inappropriate new version may cause abnormal hardware features, when the old version of the normal operation is not recommended to upgrade the driver at will. It's good for you to read the driver's Readme file first. It's just like a graphics card, the fastest-changing hardware is best not always chasing new, do not use the latest version of the driver, you should use the appropriate driver for your hardware, because each generation of drivers are for the most popular graphics chip design at the time, the old chip should not casually use the new driver, Not to use the test version of the driver, the test version of the driver will be left to the site's editors to test their system.

Solution: Go to a professional website to see the introduction of the new drive, I think the most safe way is: Graphics card with a maximum of six months after the driver; the motherboard uses the chipset for up to 6-9 months of drive; the sound card and so on most uses after one year's drive; the rear drive will not be used (unless you've tried the front driver. )。

13, loaded a lot of beta or shared version of the software

Chasing new people always like to use the latest software on their own machines, as with drivers, updates can improve performance, add functionality and compatibility, but inappropriate new versions can cause system anomalies. In particular, the test version of the program, is more harmful, since there is no official version, the software also exists a lot of uncertain bugs, these worms are like time bombs, and can explode in your system, damage your system.

The shared version of the software has some time (or times) that will fail, if your system changes some aspect of functionality through a shared version of the software, and the shared version of the software fails to function, your system will not be able to return to the state you want; The shared version of the software was disabled and could not be opened. So when you install a shared version, you should be aware that the shared version provides the number of times or times to use to avoid restoring the system and losing data.

Solution: If you do not have to use the new version to solve the problem, try to use the latest official version of the software, the test work is left to experts to complete it. Register your shared version of the software as much as possible, or you should pay attention to the limitations of the shareware software to avoid losing important files or damaging the system.

14, in the system operation of the abnormal restart

When the system is running, an abnormal reboot (including pressing the reboot key on the chassis, power supply key and CTRL Alt Del) may cause the system to lose system files, save errors, and loss settings. Originally windows was provided with a disk scanning tool, can correct part of the error file, but because the scan takes a long time, many people will interrupt his work, often this situation, but also may make the data on the hard disk error probability and the number of times greatly increased, so that the entire system crashes.

Solution: Try to use more stable system, recommend CPU frequency in 750MHz and memory above 256M users use WinXP system, others can consider WIN2000, there is the best to convert hard disk to NTFS format, it is more secure than FAT32 format, It's not easy to make mistakes. There are users of FAT32 and FAT16, and it is best to have the disk Scan tool perform its work. Of course, the best way is to find the cause of the crash, to prevent the emergence of such phenomena.

15, do not scan and defragment the hard drive

Often see a lot of people's hard drive is full of errors and fragments, always feel very bad, in fact, those things will not only make your system error probability increased, but also may make your system slow, or even run. In fact, it is very good to understand such a disadvantage, like your room to throw things everywhere, and some entangled together, and even damaged, of course, to find things to be inefficient, encounter entangled, but also to untie first, even found also can not use, because they are bad.

Solution: Usually remember to give you hard drive cleaning, every once in a while should clean up the hard drive, and to organize. If you are adding a deletion of more users, it should be sorted out in one months, ordinary users can be three months to collate. Windows's own disk-finishing tools are inefficient and can be used to improve speed with tools such as VOPTXP and Norton.

16, virtual memory does not specify the range

Virtual memory as the name implies is on the hard disk with the space of the analog memory, to ensure greater than the memory of the system memory requests, to ensure the operation of the program. General Windows defaults to Windows manage the size of virtual memory, so there are two disadvantages: first of all, the value of the request is not consistent, so the system will arbitrarily in the hard disk partition on a place to store temporary files, and then did not delete in time, so that the hard disk on the debris increased, Thus affecting the efficiency of the system. Second, general Windows is the default disk that specifies that your hard disk is stored as virtual memory. However, because many users always put the program under the same partition, so that the partition is less and less space, which means that virtual memory can use less space, less than a certain degree, will not be able to perform large software , and could not even enter the system.

Workaround: You should manually specify the location and size of the virtual memory, and in principle specify that the system's virtual memory is larger than 512M (the minimum and maximum space, to ensure that Windows does not change the location), and see if the partition has extra space to do so.

17, do not uninstall, but directly delete the folder

Many software installations will add registration information and files under the registry and system folders, and the information and files in the registry and system folders will remain in place forever if they are not uninstalled through the software's own uninstall program. Their presence will make your system large and inefficient, exceeding your endurance, and you will have to reload your system.

Workaround: Remove the program, you should go to the Control Panel to remove the Add program to execute (you can make a shortcut on the desktop is much more convenient), or in the Start menu bar to find the program in the directory of the deletion of shortcuts, through which to remove the program. There is the use of green software to avoid installation.

18, load or install too many of the same function of the software

The same function of the software is bound to exercise the same function of responsibility, resulting in disputes. I think the same function of the software should have a choice, choose the most suitable for their own use of the software. Special antivirus software should choose one on it and not load many at the same time in the system backend, loading too much will result in too much consumption of system resources, software conflicts, in the discovery of viruses, there may be because of the "fight" virus caused by the system crash trouble; Just to the multiple pop-up windows, processing separately , but also a problem.

Solution: As far as possible "one-woman", Not too flower, choose a suitable software for their own use, others can be unloaded; proper treatment of anti-virus software, should choose a virus library update fast anti-virus software, and timely update their own virus library to the latest virus library, rather than install multiple anti-virus software.

No one is perfect, he is a good comrade if he knows wrong. We have to correct some of the usual bad use of machine habits, after all, the computer is our good partner, not because of certain wrong habits and repeatedly hurt our friends

Note : More wonderful tutorials Please pay attention to the triple computer tutorial section, triple Computer office group: 189034526 welcome you to join