How to use PPT to make creative frame

micro-stereo frame and crystal frame of the production techniques (Fig 1).

1. Fabrication of micro-stereo frame

Open a blank slide in the PPT2016. Sets the background color to light gray. Hold down the SHIFT key and insert a "shape" hexagon. Right-click the positive hexagon and choose Format shape. The line is set to "Wireless bar"; The fill is set to gradient fill, type, orientation, etc. default, angle is 45 degrees, 2 gradient aperture, aperture 1 color is "white, background 1, Dark 15%", aperture 2 color is "white, background 1". Copy the positive hexagon, set it to a 225-degree angle, and right-click to place it at the bottom. Select the original hexagonal and soften its edges with the soft edges in the Effects tab, set to 3 points. The two positive hexagonal is completely coincident. Select these two positive hexagonal combinations and hold down the SHIFT key to resize the assembly. Keep copying this combination and stitching it together to form the frame you need (Figure 2).

Finally, insert a desired photo, adjust its size smaller than the frame, put it on the bottom, and with the frame overlapping combination can be.

2. The production of crystal photo frame

Make a crystal border first. Open a blank slide and set its background to "gray-25%, background 2, Dark 50%". Insert a rounded rectangle (you can drag its yellow control point to change the radian of the Fillet), and set its line to "gradient line", and the fill type is "path." 4 aperture: Aperture 1 color is white, position is 0%; aperture 2 color is "gray-25%, background 2, dark 10%", position is 8%; aperture 3 color is white, position is 65%; aperture 4 color is the same as Aperture 2, but position is 100%. The line width is set to 5 points. The inner fill of the rounded rectangle is a gradient fill, the type is path, where 2 stops: The aperture 1 is white, the position is 0%, the transparency is 100%, the aperture 2 color is white, the position is 100%, and the transparency is 90% (Figure 3).

Next, make the halo and reflective effect. Inserts an ellipse of the appropriate size, set to the wireless bar, and the interior is filled with a gradient fill, and the type is path. 2 aperture: Aperture 1 color is white, transparency is 0%; aperture 2 color is white, transparency is 100%. Copy it, rotate the copied graphics 90 degrees, so the required flare is done. Reflective production, first copy a crystal border, set the copied border, filled with "Solid color fill", the color is white, no lines. Next, draw a size fit ellipse, so that it overlaps with the copy of the Crystal border has a certain overlap, the two are selected, click on the Format tab in the "Merge Shapes" in the "cut off." Select the Cut shape, set its fill color to white, with a transparency of 80%, so that the reflection is complete (Figure 4).

Then make the bottom shadow and stand. Inserts an ellipse of the appropriate size, set to the wireless bar, and the interior is filled with a gradient fill, and the type is path. 2 aperture: Aperture 1 color is "gray-25%, background 2, dark 50%", position is 0%, transparency is 0%; aperture 2 color is "white", position is 100%, transparency is 100%. Soften the edge, the size is 5 points, so the shadow below is drawn. Then draw a cube, adjust its size, height, set its fill type is "pure color fill", the color is "gray-25%, background 2, Dark 50%", no lines. In this way the booth is also finished (Figure 5).

The final combination of crystal photo frame. Insert the picture that needs to be loaded into the crystal frame (such as the big Eye Strange yellow person), select it to remove the background color from the picture by removing background from the Format tab (you can use the 8 control points to remove the background to make the appropriate adjustments, and if you are not, you can use the "Mark areas to delete" button to remove unwanted areas), Use the "crop" and control points to resize the picture (Figure 6). Combine crystal borders, pictures, flares, reflections, shadows, and booths. Note that the picture should be placed on the next level of reflection, and the shadow will be placed on the next layer of the crystal border (Figure 7).

Small tip:

You can select the appropriate material and use "put on the bottom" to repeatedly operate until the desired effect is achieved. In addition, it needs to be noted that the above steps, where the sliding bar or digital input box adjustment range, not necessarily adhere to the number given in the case, if the production of some aspects of the effect is not satisfactory, you can also be in accordance with the allowable scope for appropriate adjustments.