See Unicom's icon is very good-looking, in the FW tried, also can draw, oh, although the steps are more, as long as careful, you will be able to draw well. Now let's draw it out.
1, the new file, width=300,height=300, the unit is a pixel. The background color is white.
2. Using the rectangular tool in the toolbox, drag and draw a square with a length and width of 100 pixels in the editing area, with a light blue fill.
3, select the Square, Edit>clone, clone A, select the cloned square, Modify>transform>numeric Transform, in the pop-up dialog box to set the length and width of 60 pixels. Then at the same time select the two a small square, modify>combine>punch. So, we got a hollow square with a border of 20 pixels.
4, select this hollow square, Modify>transform>numeric Transform, in the pop-up dialog box in the following figure set.
5. Use the elliptical tool to hold down the SHIFT key and draw a circle with a length and width of 60 pixels in the editing area, select the Circle Edit>clone to clone one, select the cloned Circle Modify>transform>numeric Transform, In the pop-up dialog box, set the following
6, select this one small two circle, Modify>combine>punch, we have a border width of 20 pixels of the circle.
7, select the Ring, Edit>clone, clone A, put it temporarily hidden up for backup. (The hidden method is to click on the layers (layer board) in front of the eye icon, when the eyes closed to indicate hidden, when the eyes open to indicate that the layer is visible layer).
8. Use rectangular tool to drag and draw a rectangle with a width of 20 pixels, high as random (but not more than 100 pixels). Select the rectangle, Modify>transform>numeric Transform, and in the dialog box that pops up, set the following
9. Move the rectangle to and from the ring and the outer circle tangent position, (this step should be careful, zoom in to move better), and then the rectangle cloned one, the cloned rectangle counterclockwise turn 90 degrees, and then move it to and the circle of the inner circle and outer circle tangent position.
10, drag and draw a smaller rectangle, (the aim is to remove the bottom part of the ring.) So that the drawn rectangle rotates 45 degrees, and then the rectangle and the circle are selected, Modify>combine>punch.
11, at the same time select the broken ring and two rectangles, modify>combine>union
12, then rotate it clockwise 90 degrees, move to the right of the hollow rectangle, such as the figure alignment.
13, select just the figure, Edit>clone, select the cloned map, modify>transform>flip horizontal horizontal flip, and then move it to the left of the hollow rectangle alignment, as shown.
14, open the circle we just hid, and then use the rectangular tool in the editing area to drag and draw a rectangle, such as picture placement
15. Select them at the same time Modify>combine>punch
16. Draw a rectangle with a width of 20 pixels and a height of 140 pixels, then move to the lower left of the half ring, drag a rectangle with a width of 20 pixels and a height of 50 pixels, and move it to the lower right of the half ring.
17, select the half ring, Edit>clone, clone One, the cloned half ring rotation 180 degrees, placed under the long rectangle, such as the figure position.
18. Clone a short rectangle and move it to the top left of the ring below. Also select this long two short rectangles and two half rings, modify>combine>union
19, rotate it-45 degrees, and place it like a picture.
20, select it, clone A, the cloned figure modify>transform>flip Horizontal horizontal flip, such as Figure alignment placement
21, the following diamond and two circles are selected at the same time, modify>combine>union
22, with a rectangular tool to draw a width of 2 pixels, longer than 100 pixels of the rectangle, and then rotate 45 degrees, clone three, the cloned two of the rotation 90 degrees, and then put the figure.
23, with four rectangles respectively and the bottom diamond hole modify>combine>punch, the final effect is as follows
Completed!!
