One-step solution to ADSL Wireless route access errors

Let's solve the problem of ADSL Wireless route surfing in one step. We will reply to you in the following article, so that you can get what you want. This makes it easy for you to learn more about the problem of ADSL Wireless route access.

If you are sure to configure the ADSL Wireless route to access the Internet step by step according to the tutorial, and keep the ADSL Wireless route to access the Internet, the device is restarted, and the ADSL light is always on, but it is still unavailable, this article may be helpful to you. Do not be confused when there is a problem, or arbitrarily suspect that there is a problem with the hardware of the device. In fact, a few simple tests can solve 95% of the problems.

Based on the problems that have occurred in technical support over the past six months, this article provides a summative explanation of how to determine the problem and solve the problem. This article only addresses the problem of multi-host internet access when a wireless route cat is configured as a routing mode, for more information about ADSL Wireless route access and connection, see [1]-No wireless network is found.

To successfully use the ADSL Wireless route to access the Internet, you must first clarify the premise that the local carrier does not provide the routing function technically. Then you need to determine two key parameters: 1. Your broadband carrier's ADSL parameter, technically called PVI/PCI parameter; 2. Your real user name and password for accessing the Internet.

If you have not yet subscribed, first confirm the premise and verify that the account and password are true. Verify authenticity only for users who used not to use Windows self-generation dial-up software to access the Internet. For example, if a third-party dial-up software such as "star speed" is used, the test authenticity step can be skipped ).

Determine whether to block the route. The simplest method for accessing the Internet through ADSL Wireless route is to call the carrier's customer service: "Is there a route ?" Or "are you allowed to connect to a vro to allow two computers to access the Internet at the same time ?". Pay attention to the Meimei reply from the customer service: if the answer is "no mail/yes", it must be no mail.

However, if the answer is "blocked/not clear/unclear", it can be understood as "the possibility of sealing is very high ". If you don't get a clear answer, you just need to check whether the people around you use a vro or go online and check what the "local" Netizens say.

How can I test the account and password authenticity? Why is there another authenticity problem with the account and password? Because some carriers adopt encryption authentication, the accounts and passwords are encrypted first and then delivered to the JU end for authentication. In this case, the encrypted dial-up client such as "star speed" can successfully dial the Internet for authentication. Only the key of the encrypted dial-up client is the same as that of the JU end.

Window self-generated dial-up connections without a key) can not be connected to the JU end key, of course, the verification will fail. Using this principle, we use the Connection Wizard provided by Windows to create A new PPPoE dial-up connection, which is called "connection ", of course, you need to add the ADSL account and password at the time of creation, at least you think it is correct), and then use "connect A" to pass the current ordinary cat dial-up trial ......

If you successfully log on to the Internet, at least two things are proved: 1. the user name and password you remember are correct. 2. Your JU end does not adopt encrypted authentication. the user name and password you know are authentic. If the system prompts that the authentication fails: either the password is incorrect or the encryption is performed on the JU side. Some of this encryption can be cracked. Please search for "star brute-force cracking" on a hundred pages. There are many tutorials on the Internet ~

We strongly recommend that you complete the above steps before you subscribe to the route device, to avoid unnecessary misunderstanding and trouble after the order, because if the account authenticity test fails, there is no need to remove the package to get the new device configuration.

The account test is okay. you have configured the PVC parameters step by step as per the tutorial. If you think the correct PVC parameters are not available, let's do a few tests to see where the problem is. You need to believe that this is a complete troubleshooting process, please strictly follow the steps yellow as the key) test. 90% the problem lies in ADSL parameters and other objective environments.

Here, we first exclude the parameter errors: Most customers do not know why they need to know the ADSL parameter VPI/VCI. Because the Modem has a built-in Modem, this parameter is more than the general router configuration. The simplest way to obtain parameters is to call customer service and directly ask for the PVI/PCI parameters of ADSL. The chance of a positive response is very small.

If you don't get a reply, call the phone again and use the method I taught you to ask: I lied that my cat was broken and got a USB cat, this cat has to set these two parameters to inform customer service of your approximate location. In some cities, the JU parameter is different.) It makes no sense if she doesn't tell her.

In this case, you can take advantage of the technical support information that a legitimate consumer deserves ...... This method works normally. If you don't ask, doesn't it matter? Can you check it online ...... If you still cannot determine whether to connect to the Internet through the ADSL Wireless route, determine the parameters according to our method.

◆ Select "Restore factory settings" or "Restore Default Settings" in the routing device menu ". Please note that DHCP is disabled by default in ZTE 531B dark blue. For devices with the DHCP function disabled, You need to manually configure the nic ip address as 192.168.1.11 and subnet mask 255.255.0 to connect to the device menu. How do I manually set an IP address? See Practical network basics.)

◆ Connect the debugged computer to the wireless router cat through a wired connection to ensure that this is the only computer connected to the route to use the safest environment for debugging ). By default, all route cat configurations are in full bridge mode, that is, all seven sets of bridge parameters are in the country. Connect the ADSL telephone line to the routing cat so that the connection test regards the routing cat as a common cat.

◆ When ADSL/DSL lights are always on, use the account to test the new "connect to A" dial-up Internet access. The message "remote server does not respond" is displayed. Check whether the route cat configuration is in Bridge Mode. If not, follow step 1. If the problem persists, you can switch to another ADSL line for testing. It is best to switch to another ISP line, where the carrier line is incompatible with the device. After resetting the device and changing the lines of different carriers, please contact us after-sales.

The prompt "Verification Failed" is displayed. It is very likely that jufang has bound a MAC address, which is only required to unbind the phone number of the carrier. If the prompt "Verification Successful" is displayed, it should at least prove that the ADSL Bridge Pipe is connected. That is to say, there is no problem with the cat's hardware and one of the seven sets of parameters is correct, so proceed to the next step.

◆ Log on to the device menu and delete one of the most "reliable" parameters from the preset PVC parameters. Save the configuration, restart the device, and then use "connect A" to dial up the Internet. Good luck. The deleted one is correct. Of course, the dial will fail. If you have not deleted the correct one, you can successfully dial again from your computer. According to this principle, delete a group, save it, and dial once. After you delete a group of PVC, the computer dialing will fail, and the correct parameter will be found out, we call this set of parameters "parameter C ".

◆ Restore the factory settings once the operation in step 1 is performed ). Log on to the ADSL Wireless route surfing device menu, delete the six sets of bridging PVC parameters other than "parameter C" in the preset PVC parameters, and then use "connect A" to dial up the Internet from the computer, if the dial is successful. Then "parameter C" must be the ADSL parameter of your carrier on the line you tested.

So far, you have at least known the real and correct user name and correct ADSL parameters. Use this information to configure the PPPOE connection of the route cat according to the tutorial, and save and restart the router. After the device normal sequence: Power green light always on self-check passed) --> WLAM light always on/flashing wireless module started) --> DSL light flash signal synchronization) --> DSL light always on synchronization completed) --> Internet light flash dial-up attempt) --> Internet light always on successfully login) --> Internet light flash data transfer), this process varies with the environment and equipment, it takes 2-5 minutes. Log on to the device menu and check the device status ......

You can see that the figure only proves that your cat is already connected to the Internet in the routing mode. Generally, terminal devices, computers, mobile phones, PDAs, game hosts, and Wei. Xing decoding devices can access the Internet as long as they can be connected to the routing devices through wired or wireless connections. Note: The NIC of these devices must be set to automatically get the IP address and DNS address. How can I set to automatically get the IP address? See "Practical network basics").

If the ADSL account password and PVC parameters are verified correctly, the above picture is still not displayed for 10 minutes, although the probability is small, however, it may be because the operator technically restricts the problems of the routing device or the routing device itself. At this time, we recommend that you reverify the correctness of the parameters according to the above method, check the connection between the line hardware, and repeat the ADSL Wireless route to access the Internet again. In addition, there is a useful information available, that is, the log record of the router ......

If it is always unsuccessful, save the log of the vro and contact us for a solution. Generally, customers think that they can access the Internet by reading web pages and chatting via QQ. Even if they can access the Internet, this is a popular criterion for judging. Generally, the professional judgment is to test three Ping packets. Obtain the IP address of the gateway and DNS in the NIC status, such as the computer in the office and the Internet access parameters of the ADSL Wireless route ......

Generally, the address of the route CAT/router device is the gateway address. The DNS server is allocated by the carrier. First ping the gateway, Then ping the DNS server, and finally ping whether the IP address can be correctly resolved and connected. For more information, see practical network basics. If the gateway cannot be pinged, it is an internal network problem. The next two cases are complex. you can contact us directly to solve the problem of ADSL Wireless routing.