T60 Fan Error solution. Transferred from ZOL product Forum-author zxymb

Recently, Xiao Hei's fan was so loud that he didn't pay much attention to it. However, the sound of the car caught up with the tractor in the past two days. I know it must be a fan problem, but I have been too lazy to start it, who expected to prepare the paper early this morning?
Suddenly there was a strange noise, and the hacker started the error and prompted: fan error thought it was an accidental error and restarted n times again. the problem still exists. It seems that it will be removed, anyway, I have already prepared a big split. Because of my previous experience, I went out to buy a needle tube and got a bottle of oil and the necessary silicone grease. You should pay attention to the oil. It is best to stick it and call the butter. Note: The butter here is not food, it is on the bearing. The butter is not very good, you have to take the fan completely apart, the oil is much more convenient, the needle can hit the inside.
 

Start the next step. Remove the screws at 1.1. You can easily remove the screws with some hands-on capabilities. After the screws are removed, the next step is to split the palm rest. The Palm rest is very good, but pay attention to the following fingerprint chip cable, Gently pick the tweezers and pick it down, the keyboard is the same, as long as the screw is screwed down, the keyboard itself is relaxed, or the same, please be careful to lift up, gently pick the cable.

Then there is the fan, and the removal of the fan is also very simple, pay attention to the above line and the middle of the iron on the number, but note that the above baffle should be removed before the removal, the 2-Side Pull to the top of the inside can be pulled down, ibm industrial design is really good, consistent with the good, I use a lot of strength to remove, then, you need to fill the oil with a gray brush. It is best to pull the aluminum foil on the side of the fan when the fan is grayed out, because it will be split later. There will be a lot of dust inside, brush it out with a brush,

I tried it several times and found that the sound was still working. So I continued to split the fan and split it completely. This step was also difficult. The copper was very soft and it could be opened easily with fine pliers, this is the only way to do it. Now you can brush it!
 

Fan Blades are much easier to split than I thought. They don't need to be forced. When we pull them down, we need to note the oil. 2 drops of holes in the middle,

Do not get too much, it will flow oil, this type of fan I still recommend using butter is better, there is no hand, can only use this, after the injection of the Assembly tried, completely back to normal, haha, so excited,

 

Silicon grease, don't say you don't know what it is.

 

The silicon grease is going to be on the cpu, and the original one is hard, so I bought a new one.

Finished !!

We all know that the ibm fan is very expensive. I spent a total of more than 500 genuine fans.

Needle Tube 5 hair

1 large bottle of oil 2 yuan

Silicon fat 5 hair

3 yuan solves the problem of spending more than 500 fans. In fact, there is no need to change the fan, and you can solve it by yourself.

It should be noted that the position of each screw should be remembered. It is best to mark the mark, because it is difficult to screw in because of an error. It is best for everyone to record the screw number like me, to avoid installation of many things, you must be careful and bold in disassembly and installation, and avoid impatience. In addition, it is risky to disassemble the machine. It is not recommended to operate on persons with poor hands-on capabilities, we do not recommend that you have any warranty.

Now, let's take a rest. We have a lot of support. This is the first post of younger brother. You can support it !! Thank you.

Qq: 8635647. You are welcome to harass me. If you have any questions, please contact me ~~ Note: ibm