Use calculation and repair tools to rub skin freckle on many spots

Material characters face more spots, with the passage and calculation to wear the skin is more efficient; just choose the right channel, and then use a few calculations to get the spots of the selection; In the layers of the panel, you can remove most of the spots, later with the use of stamps and other tools to eliminate some flaws.

Original

Final effect

1, open the original image, copy a layer, into the channel. Observe the red, green, blue three channels, compared to the blue channel texture stronger, especially the spot part of the clear show.

Remember that the channel is a selection, it is independent and attached to the original image used to save the selection of black and white images, the default white indicates that the selected black is not in range.

2, select the blue channel, copy the Blue channel, select the blue channel copy, back to the menu bar---filters---other---High contrast retention, radius set to 9.6, where the numerical settings vary depending on the quality of different graphs, and then determine.

3, continue the menu bar---image---calculation. The channel in Photoshop is a powerful container, and computing is an important command to mix or select the channel. In the calculation command, the source 1 source 2 does not move, the blending mode is changed to strong light, the aim is to further enhance the contrast effect on the blue copy channel, so as to more accurately calculate the spot of the selection we need. Once you are sure, repeat the same calculation command two times.

4, back to the channel panel, there are more than three channels in the channel named Alpha, the left hand press the keyboard CTRL key, mouse click Alpha3 channel thumbnail to generate a selection, point RGB layer back to the level of the surface board.

5, look at the picture, the ant line of the selection made by the good skin and spots and darkened part of the distinction is very clear. Now point Select---reverse, the previous said the default white indicates that the selected black is not in range, now because we have to deal with the spot part. In order not to affect our visual effects, easy to observe here I think it is necessary to hide the selection, shortcut keys ctrl+h.

6, on the surface of the graph to establish a curve command, set the following figure, the numerical setting depends on the figure. The aim is to improve the brightness of the part of the skin that affects the complexion only because of the darkness, and it also blends more with the good complexion of the constituency, narrowing the parts to be dealt with, and thus the area of the spot is more clear.

Then select the Brush tool, opacity and flow rate set to 50%, the hair and face around the ear and wipe, do not have exposure to the situation, eyes, eyebrows and lips with 80% of the brush to erase. Observation of the image, skin color significantly improved, spots become clear dots, texture is also good.

7, cancel the constituency. Do the stamping layer, enlarge the image to 200%, select the Clone Stamp tool, reduce the tool to 8%, opacity and flow set to 90%, with the keyboard Alt key to a spot for processing, avoid the whole piece of the slide past repair, or tool diameter too large and destroyed the original texture.

Press and hold the ALT key of the keyboard, the mouse in you want to dispose of the spots next to clean place to press sampling, and then loosen the ALT key, and then press the mouse at the spots, sticky paste on the clean skin, where the need for patience and careful. Be sure to take a sample of the spots that are close to where you want to handle them, so that the skin is closer and there is no abrupt connection.

8, the repair process to constantly enlarge or reduce the image, compare the view and look for missing flaws. Until the spot repair is complete, under the admiring, is also good, the skin color natural texture intact.

At this time, the use of grinding software to correct the appropriate. For example, the Portraiture tool, set the following figure, after the same selection of brush tool, opacity and flow set to 70%, the hair and face around the ears and parts of the wipe, eyes, eyebrows and lips with 90% of the brush to erase.

To do the stamping layer, spot repair completed, according to their own skin love to continue to the image of skin tone adjustment, here do not explain this, complete the effect diagram below.

Note : More wonderful tutorials Please pay attention to the triple Photoshop tutorial section, triple PS group: 182958314 welcome you to join

Category:

• PS Image Processing
• PS Grinding Course