Others

At present, the development of Ethernet switches is very rapid. Here we analyze the development status of Ethernet switches. MPLS switches follow the trend of combining ATM and IP addresses. Multiprotocol Label Switching (MPLS) is a tag exchange

The embedded storage exchange technology is still quite common, So I studied how to increase the reliability of the embedded storage exchange technology. Here I will share it with you and hope it will be useful to you. The embedded storage switching

Layer-3 switches are quite common, So I studied how to use layer-3 switches to ensure data security. I would like to share with you here, hoping they will be useful to you. The backbone network topology of Jiangxi sanjiu yigong Co., Ltd. is

IT experts based on the D-LINK Switch configuration Q & A set, now there is a huge controversy about the configuration of the D-LINK switch, there may be people do not know how to configure the D-LINK switch, IT doesn't matter, after reading the

Pay special attention to the PVLAN configuration steps and precautions of the Huawei 3COM Switch. There are many articles about the configuration. You should pay more attention to the precautions related to the PVLAN configuration of the Huawei 3COM

The 10-ge core switch is still quite common. So I studied the perfect design concept of the 10-ge core switch and shared it with you here. I hope it will be useful to you. Quidway S8500 series 10-Gigabit core switches are a new generation of

This section describes the standards that stack switches must meet. Many people do not know what Stack switches are. Let's give you a detailed introduction today. We hope relevant users can get what they want. A stacked switch is a type of switch.

Because smart switching performs simultaneous data exchange on most ports, it requires a wide switching bus bandwidth. If a layer-2 switch has N ports, multiple Access ports and low prices provide a perfect solution for small network users. In order

You can transfer data between multiple port pairs at the same time, and then assign different priority levels to different streams, you can process network data more efficiently without compromising data exchange performance. There are many things

In today's society, the most commonly used vro is the number of routers, because it is relatively cheap and its functions are no different from those of vswitches. However, layer-3 vswitches are indeed more powerful than vrouters, then we will study

The soft switch technology is one of the most popular technologies in the current technology circle. Nowadays, many switches can provide high-speed connection ports that support fast Ethernet or FDDI. I hope this article will provide you with

Generally, each port of a layer-3 switch is used to connect to an independent CIDR block. However, to provide faster access speed, you cannot directly connect the input/output ports with different rates, it is also prone to packet loss. We have

Since Layer-3 switches can be considered as composed of routers and common switches, You can first try to install some modules with routing functions during assembly, in this way, there is a layer-3 Switch rich in routing functions. Its functions

An important indicator is often mentioned in the performance parameters of core switches: TRUNK. Many L2 switches can better solve the conflicts between cost and performance when introducing their performance, the following is a study. What

The configurations of vrouters and vswitches of different models are also different. Therefore, in this learning, we need to learn a common method. Vswitch configuration has always been mysterious, not only for general users, but also for the vast

VswitchThe following figure shows the instance topology configuration: Basic vswitch Configuration Switch> enable  Switch# config ter   Switch(config)# hostname Switch  Switch(config)# interface vlan 1   Switch(config-if)# ip address 192.16

Port Channel configuration command 1. port-group Command: port-group [port-group-number] [load-balance {src-mac | dst-src-mac | src-ip | dst-src -ip}] No port-group [port-group-number] [load-balance] Function: Create a port group and set the Traffic

Cabling SystemThere are two methods: "field" and "well. The "field" is more suitable for the layout of the ring data center, and the "well" is more suitable for the layout of the vertical and horizontal data center. Its location can be arranged

Next I will explain the TP-Link Wireless route security configuration diagram). According to the figure below, I hope the majority of users will give me some suggestions, preferably those who have experienced the suggestions. Thank you. The security

In this article, the di-740p model of the Broadband Router D-Link, the default Management address is 192.168.0.1, the Management port is 8080. Set the IP address of a computer and the router management address in the same network segment. For