Others

Connect the LAN of Route 1 to the WAN of Route 2, and then Connect the network cable from the LAN port of Route 2 to a computer.Start Configuration 1. settings on the local machine1: Open the network neighbor, attribute 2. In the pop-up local

Assume that you use PPPOE to access the Internet through the first vro.WAN port connection type selection: PPPOE (usually static IP, dynamic IP, PPPOE, dynamic DHCP)The LAN port is set as follows: IP: 192.168.1.1 mask: 255.255.255.0 gateway and DNS:

    An external LSA (Class 5 LSA) is used to advertise each external route that is redistributed from other protocols (such as OSPF) to OSPF. In ASBR, five types of LSA can be summarized and injected into the OSPF domain. R1 Configuration: Interface

The official CCNP teaching material emphasizes 0. In fact, no matter the outbound interface configuration or the Management Distance configured with the next hop address is 1. The experiment is as follows:   R1 (config) # ip route 1.0.0.0 255.0.0.0

It is common for dhcp server to allocate IP addresses across routes or VLANs. Here we will show how to allocate IP addresses of DHCP servers across routes. The topology does not need to be too complex, it mainly demonstrates the general method. Lab

As we all know, some vro models support the 3G function. The following describes how to use the vrovol.1. Configure the 3G Function of the VOLANS RouterInsert the 3G Nic into the USB interface of the vrousb, enter the configuration interface of the

 Generally, the company uses VE1260, the branch uses VE982, and the Intranet uses a layer-3 switch, which divides VLAN, and establishes a pptp vpn between VE1260 and VE982. After the branch transfers the Intranet VPN to the company, you can access

Generally, when we configure svpn for the volans router, we will encounter an unsuccessful situation. Next, I will introduce the specific factors and solutions.1. The external line connected to the SVPN client must be connected to the WAN1 port.2.

We know that no matter how the WAN interface IP address of the youxun router changes after DDNS is configured, Internet users only need to remember our dynamic domain name and can log on to our Intranet server at any time. The configuration method

Presumably, network administrators have a headache for configuring a large number of complicated configuration commands for Huawei routers. The following is a simple configuration command for Huawei routers. Let's take a look!1. Common User Mode (1)

Vro is one of the hardware devices that network administrators often need to deal with. If you forget the vro password, you will be given two tips to solve the Cisco password problem.The boot options in Cisco IOS software need to understand some

When you use a computer to connect to the network, the local connection is restricted or there is no connection error, resulting in wireless connection to the network. The following describes several solutions:1. Check whether the DHCP assignment

In some cases, we need to directly connect the two routers. This article will detail how to set the route entry, as shown in the following figure, the method of connecting LAN routes is marked first: (connecting LAN ports to downlink LAN ports is

The process of establishing the relationship between the two routers is established before learning the relationship between OSPF and establishing the neighbors. After router A running the RIP Protocol is started, it sends A request packet to the

How to access a vro on the lingke terminal and set up a vro is usually done by logging on to the vro Management page. However, some high-end vrouters sometimes need to be controlled through the console. Next, I will take the lingke router as an

In order to ensure network security, the firewall is essential. Next I will take the mercury router as an example to introduce the firewall settings.1. IP address filtering in the firewall is used to set the Intranet host's access permissions to the

As the DHCP settings of the vswitch, the router switches the wireless route of the vswitch to the AP mode to connect to the wired router. Disable the DHCP service built in the wireless router for the Wireless AP to use, but sometimes the computer

Before setting up a universal router, if you want to set up a router to access the Internet, you must enter the router to set up the router. Today, we will introduce the preparations before setting up the universal router, for more information, see.

The routing protocol can be divided into Static Routing and dynamic routing. Static Routing: it is a fixed route information manually set by the Administrator in the router. Static Routing cannot reflect network changes. It is generally used in a

When the H3C communication router fails, the switch line is analyzed. When one of the Two-line routers fails, all data is automatically forwarded to another line, but what should we do if there is no automatic switch failure?1. In the network