Others

The script consists of four files: tar. sh-> loop. sh-> loginfo. exp. The script logs on to each vswitch in sequence, runs the "tftp 192.168.36.44 put vrpcfg.zip" command on each vswitch, and renames the saved configuration file to the corresponding

Switch fault types and analysis methods 1. Switch fault classification switch faults can generally be divided into hardware and software faults. The hardware mainly involves power supply, backplane, port, and module faults. Www.2cto.com 1. Check

The vro configuration command of a common switch in Digital China enters the privileged mode: enable; view the configuration information: show run; www.2cto.com returns to the privileged mode: ctrl + Z; enter the global configuration mode: config;

For example, management interfaces connecting the console to a vswitch through a serial portWww.2cto.com open the Super Terminal on the computer to create a new terminal connection www.2cto.com set interface properties press the Enter key to enter

SAN Switch license activation step 7450-7451 does not support cascade by default, that is, E_Ports, requires activation licenses for fc # Full Fabric (if MES is upgraded, Full Fabric number is fc ), A maximum of 10 Fabric servers are supported. The

Brocade 5100 vswitch alias configuration method alias configuration command www.2cto.com alicreate "comment", "" alicreate "wolf_p770db_00000000br7", "" alicreate "wolf_p770db_0000br15 ", "" zonecreate "comment", "comment; comment" comment create

Cause of err-disable on the switch interface and solution if the interface status is err-disable and show interfaces status err-disabled, you can view the cause of err-disable triggering. Several common causes of switch interface err-disable caused

1. S2000-HI series Ethernet switches support three types of Ethernet Port Link: Access type: port can only belong to one VLAN, generally used to connect to the computer;Trunk type: the port can belong to multiple VLANs and can receive and send

In practice, ruijie [instance] VLAN + SVI + MSTP + VRRP + port AggregationThe topology is as follows:PC0, PC1, PC2, and PC3 belong to vlan 10 vlan 20 vlan 30 and vlan40 respectively.Tutorial steps:Step 1: Create a vlan on the vswitch and configure

Use the vswitch to share the copy and transfer file windows7: 1. use two (or more) computers with two network cables. one end of the network cable is connected to ports 2x and 3x of the switch, and the other end is connected to the computer and

Data communication and network notes-exchangeIf there are multiple devices in the network, how can we connect them for one-to-one communication? A good solution is switching ).Exchange methods are classified as follows:Packet Switching has been

Hub, L2 Switch, router, and L3 switch hub: Previously 10 m shared Ethernet dedicated, currently used less, only work in the physical layer, port and host use half duplex communication, generally, no matter whether the physical connection is bus or

Vlan switching technology Vlan is built on a LAN switch and implements division and Management of logical working groups in a software manner. Its Switching technology generally includes port switching, three types of frames exchange and Token

The Huawei Switch configuration command [Quidway] dis cur; displays the current configuration [Quidway] display current-configuration; displays the current configuration [Quidway] display interfaces; displays the interface information [Quidway]

An Analysis of the Application of HIS in case of switch port congestion to greatly improve the efficiency of hospital work. With the development of hospital services, HIS is growing and more problematic. This article introduces the analysis and

I accidentally forgot the password of the VSS 6 admin user (this proves my carelessness). I Googled and found the following information: The secret is to hack the um. dat file to remove the Admin password From offset 80 the bytes are (all numbers

The routing function of a Cisco layer-3 switch is configured on the Link Layer. A layer-2 switch has no routing function, that is, it can only communicate with machines in the same network segment. Www.2cto.com and the layer-3 switch can configure

Quick Switch replacementIf a switch or vro cannot be started at all, we need to replace a backup vswitch of the same model to replace it. First, we need to power up the switch in a non-business environment. Make sure that the new switch can

Our work on information security has recently been suspected of using some tools for network attack access, which indeed affects network security. In order to improve the security of network access, in this case, no other software tools are used to

H3C-S5500EI switch QOS policy configuration if there is a H3C-S550EI L3 switch in the enterprise and you want to make some restrictions, such as allowing those IP addressesIf you can access the Internet, you can use the QOS policy for configuration.