MA5100 resizing Configuration

MA5100 resizing configuration # configtNM_DWK_SQ_MA5100_A (config) # interfaceadsl02 (Slot Number) NM_DWK_SQ_MA5100_A (config-ADSL-02) # blockallNM_DWK_SQ_MA5100_A (config-ADSL-02) # con

MA5100 resizing configuration # config t NM_DWK_SQ_MA5100_A (config) # interface adsl 0/2 (slot) NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # block all NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # no block all NM_DWK_SQ_MA5100_A (con

MA5100 resizing Configuration

NM_DWK_SQ_MA5100_A> enable

NM_DWK_SQ_MA5100_A # config t

NM_DWK_SQ_MA5100_A (config) # interface adsl 0/2 (slot number)

NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # block all

NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # no block all

NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # activate all 4 (template number)

NM_DWK_SQ_MA5100_A (config-ADSL-0/2) # exit

NM_DWK_SQ_MA5100_A (config) # multi-pvc adsl 0/2 0 xffffffff region lan 0/13 vlanId

100 (Business vlan) off 1 1

NM_DWK_SQ_MA5100_A (config) exit

NM_DWK_SQ_MA5100_A # save

MA5100 (config) # show board 0 // view box

MA5100 (config-ADSL-0/4) # show board 0/0 // view board user online

MA5100 STARTUP configuration 16: 04MA5100> enable

MA5100 # system name DYTELE_5100; 5100 Host name

DYTELE_5100 # configure terminal

Dytele_5100( config) # interface lan 0/13

DYTELE_5100 (config-LAN-0/0) # vlan add; added 1483B in-band network management vlan

{1-4095}: 4000

{General, region}: general

{0x1-0xff}: 0x01

DYTELE_5100 (config-LAN-0/13) # default-vlanid; set port default vlan id

{} {0-7}: 0

{1-4095}: 1

[Port default VLAN description]: sets the port vlan id of port 0 to a value different from that of the network management VLAN and service VLAN. This aims to forward packets of both the network management vlan and service vlan.

DYTELE_5100 (config-LAN-0/13) # operation-mode ipdslam; modify the lan board operating mode to ipdslam to support 4 kvlans

DYTELE_5100 (config-LAN-0/13) # port mode

{General, ipdslam, ipcascad}: ipdslam; consistent with the lan board operating mode

{} {0-7}: 0

{Tagged, untagged}: tagged

{Negotiate, non-negotiate}: non-negotiate

{Half-duplex, full-duplex}: full-duplex

{10 m, 100 m}: 100 m

{Pause-frame, non-pause-frame}: non-pause-frame

[Note]: It is recommended that the uplink Ethernet port be set to m full duplex without self-negotiation, and the working mode of the corresponding port of the Peer device be set to m full duplex.

DYTELE_5100 (config) # pvc nms; Added Network Management pvc

{Ipoa, 1483b}: 1483b; select 1483B.

{Llc, vc}: llc; select the llc Encapsulation Format

{} {32-63}: 32

[Note]: VCI is deployed on the SAR layer and used for debugging the PVC of the network management. You can select the VCI When configuring the network management data, for example, 32-63 or not, press enter and select anyvci, which is automatically generated by the system.

{Atm, adsl, lan, fr, ces-sdt, ces-uni, ces-udt, ces-v35, nms, aiu}: lan

{(0)/(0-6) or (9-15)}: 0/13

{1-4096}: 4000

{1-5000}: 1

{1-5000}: 1

DYTELE_5100 (config) # atmlan ip-address atm/ethernet; set the 5100 in-band network management ip address

: 172.30.17.X

: 255.255.254.0

DYTELE_5100 (config) # nms name

(S [15]): SLTX_BMS

: 172.30.17.1

(S [31]) [public]: public

(S [31]) [private]: private

{In-band, out-band}: in-band

DYTELE_5100 (config) # nms activate

{}: 172.30.17.1

DYTELE_5100 (config) # atmlan ip-route; route added to the network administrator

: 172.30.htm

: 255.255.254.0

: 10.10.1.1; uplink low-end switch address

DYTELE_5100 (config) # atmlan ip-access; added the allowed access list

: 172.30.17.1

: 172.30.17.254

: 255.255.255.0

DYTELE_5100 (config) # multi-pvc

{Adsl, lan}: adsl

{(0-4)/(0-6) or (9-15)}: 0/0

{0x1-0xffffffff}: 0 xfffffff

{Region, vpi}: vpi

{0-127}: 0

{Vci-range, anyvci}: vci-range

{32-127}: 35

{32-127}: 35

{Adsl, lan}: lan

{(0)/(0-6) or (9-15)}: 0/13

{VlanId, anyvlanId}: anyvlanId

{1-4095}: 8

{1-4095}: 1000; vlan data depends on Requirements

{Both, up, down, off} [off]: off

{0-7} {off} [off]: off

{1-512}: 1

{1-512}: 1

DYTELE_5100 (config) # adsl line-profile add 3; add traffic TEMPLATE 3

DYTELE_5100 (config) # interface adsl 0/0

DYTELE_5100 (config-adsl-0/0) # active all 3; activate all adsl ports traffic TEMPLATE 3

DYTELE_5100 # save; save the Data configuration

Detailed configuration of MA5100 5103 5105

5105 Configuration

> User name (<20 chars): root

> Password (<20 chars): admin -- enter user mode

MA5105 # user password -- Change user password

> Old password: admin

> New password (<20 chars): qdtele! @#

Password modified successfully

MA5105 # configure terminal -- enter global configuration mode from user mode

MA5105 (config) # hostname

(S [49]): SJDS_MA5105 -- change the device name

> Are you sure to modify system name? (Y/n) [n]: y-confirm Configuration

Set successfully.

SJDS_MA5105 (config) # atmlan ip-address Ethernet --- this command is used to set the ip address of the device's Ethernet port. The ip address must be in the same network segment as the ip address of the configured terminal or gateway, the IP address and mask must also comply with network specifications. If a system route exists when you set the route, and the gateway of the route is not in the same network segment as the IP address of the device, the setting will fail. Delete the route and then set the IP address of the device.

: 222.173.126.2 255.255.255.255.255.255.20.- enter the IP address and mask of the device as required by the ticket.

SJDS_MA5105 (config) # atmlan ip-route

: 0.0.0.0 add an upstream route according to the ticket

: 0.0.0.0 allocation. Please confirm with the data

: 222.173.126.1

Add route successfullyet successfully.

SJDS_MA5105 (config) # atmlan ip-access

: 222.173.125.1 other network segment, you must also add a route gateway, if the address is 222.173

: 222.173.125.253. 126. **, or 222.173.125. **.

: 255.255.255.0 is another address segment, for example, 192.168.0. *,

Add acceptable IP address successfully. 192.168.0.1 192.168.0.254 255.255.255.0

Note: When the firewall is changed, delete the address segments that are no longer secure. For a host that accesses the system through Telnet with an in-band network management, the address must be within the range of the addresses allowed to access the system. Add an acceptable IP address segment. The no form of this command is used to delete an acceptable IP address segment.

SJDS_MA5105 (config) # atmlan ip-access 222.173.125.1 222.173.125.253 255.255.255.0

SJDS_MA5105 (config) # atmlan ip-access 219.146.4.1 219.146.4.10 255.255.255.0 --- allow the address of the N2000 Network Administrator server to access all the site configurations.

SJDS_MA5105 (config) # atmlan ip-access 222.173.64.1 222.173.64.254 255.255.255.0 -- allow access from 5200F (the CIDR Block of the 5200F LOOPBACK address)

SJDS_MA5105 (config) # atmlan ip-access 222.173.65.1 222.173.65.254 255.255.255.0 -- allow access from the upstream device (the network segment of the ne loopback address)

SJDS_MA5105 (config) # nms tagged 10-Add a network management VLAN 10 and add a management vlan. All bureaus use the same management vlan 10. For details, see the following table, please confirm with the data

Y-confirm Configuration

SJDS_MA5105 (config) # interface lan 0/0 -- enter the LAN board configuration mode box number/slot number in global configuration mode, with a value of 0/0

SJDS_MA5105 (config-LAN-0/0) # port mode tagged non-negotiate full-duplex 100 m-configure the active connection mode for non-self-negotiation, full duplex mode

SJDS_MA5105 (config) # snmp-server community bms 219.146.4.2 public private notify 162 v1 ----- configure network management parameters

Ii. Business Configuration

SJDS_MA5105 (config) # adsl line-profile add 3-configure the line template (1 M, 2 M)

After entering, see "y" and press "y" for the rest. Change 6144 to 1024 and change 614 to 256 only when the rate command is prompted.

SJDS_MA5105 (config) # interface adsl 0/1-enter the 1st slot Board

SJDS_MA5105 (config-ADSL-0/1) # no block all/deactive all-deactivate slot 1 all user ports on the board

SJDS_MA5105 (config-ADSL-0/1) # activate all 3-bind speed TEMPLATE 3

SJDS_MA5105 (config-ADSL-0/1) # exit

SJDS_MA5105 (config-ADSL-0/2) # interface adsl 0/2-entry 2 slot Board

SJDS_MA5105 (config-ADSL-0/2) # no block all/deactive all-deactivates all user ports on the board at slot 2

SJDS_MA5105 (config-ADSL-0/2) # active all 3-bind 3 rate Template

SJDS_MA5105 (config-ADSL-0/2) # exit

SJDS_MA5105 (config) # interface lan 0/0-enter the lan board and add service VLANs. Configure 32 VLANs according to the ticket. manually configure the VLAN or configure the service by script. the operation method is the same.

SJDS_MA5105 (config-LAN-0/0) # vlan 100

SJDS_MA5105 (config-LAN-0/0) # vlan 101

SJDS_MA5105 (config-LAN-0/0) # vlan 102

SJDS_MA5105 (config-LAN-0/0) # vlan 103

SJDS_MA5105 (config-LAN-0/0) # vlan 104

SJDS_MA5105 (config-LAN-0/0) # vlan 105

...... Assigned by ticket, 32 VLANs in total

SJDS_MA5105 (config-LAN-0/0) # exit

SJDS_MA5105 (config) # pvc adsl 0/1/1 0 35 lan 0/0 tagged 100 1483b 0 on 1 1-add business PVC where 0, 35 is fixed.

Add PVC successfully, CID = 2.

Similar

A total of 32 entries need to be added, and the adsl port ranges from 0/1/1-0/1/16 0/2/1-0/2/16. The vlan sequence increases, and the rest remains unchanged ........

3. View configurations

Show board 0 view board status

Show board 0/1

Show board 0/2

Show efs view version

Run the show version command to view the system version information;

Show board 0/0 view the MIEA plug-in board and the status of port E1;

Show board 0/1 or show board 0/2 to view the port status of the ADLA board;

Run the show adsl template 0 command to view the configuration information of all the ADSL templates in the system;

Run the show pvc command to view the PVC connection information configured by the system;

Run the show atmlan ip-address atm command to view the system ip address Configuration;

Run the show atmlan ip-route command to view the system route configuration information;

Show atmlan ip-access command to view the list configuration information that the system can receive;

Run the show atmlan mtu command to view the MTU value settings of the interface;

Run the show line parameter command to view the ADSL line configuration parameters;

Run the show line operation Command to view the running performance parameters of the activated port's ADSL line;

Show line failure command to view ADSL line fault statistics;

Show alarm history command to query system alarm records;

The show log command is used to query operation log information.

By using the preceding commands, you can check whether your configurations meet your business needs and whether your configured services are complete.

SJDS_MA5105 (config) # pvc adsl 0/1/1 0 35 lan 0/0 tagged 100 1483b 0 on 1 1-add business PVC where 0, 35 is fixed. Among them, 0 35 is the pvc of various places, which is not fixed and unchanged. Because of the city and city, the upstairs is obviously a copy. Do not forget the most important save Haha Note: When the tagged mode is changed to untagged mode, Step 1: no pvc all 2: no vlan 3: no nms 4: port mode untagged