Netgear R6250 routing from OpenWrt or DD-WRT system to default system for small white

original In this connection, fit R6250 . I am by the way to detail the steps, lest the next time there is little white encounter this problem, too much time to delay. http://www.right.com.cn/forum/thread-155203-1-1.html

1. Download the relevant firmware

Version 1.0.0.62 Full Name: R6250-v1.0.0.62_1.0.62.chk this is R6250 The first initial firmware can be downloaded to the website.

2.telnet or SSH Login R6250 (penwrt or dd-wrt)

Note:

① initial can be used telnet Login 192.168.1.1 , no password required, use passwd Root , after setting the password, telnet The service is automatically closed.

②defaultWin7not opentelnetand theTFTP, please see this for more details.telnetthe button below isTFTP. http://jingyan.baidu.com/article/870c6fc3cd6fa9b03fe4bee4.html 

③I'll use it on my own computer.telneteven onR6250,and then usepasswd Rootcommand to change the password. re-useXshell sshToolsConnectionR6250routing.

-------------------------------------------------------------------------------------------

The following steps are SSH Connection r6250 the command that was made.

3. go to the temp directory

Cd/tmp

use the following command to download the firmware directly in the current directory Note: Routing must be available online.

wget/HTTP/official address/r6250-v1.0.0.62_1.0.62.chk

I'm using a different method. in the SSH Login Netgear after installation sftp software for easy uploading of firmware Note: Routing must be available online .

opkg updateopkg Install Openssh-sftp-server

Use vsftp Login then upload the local downloaded firmware (I use Xshell Software xftp to log in and upload)

5. (***openwrt in * * *) if the current system is OpenWrt Execution

MTD-RF Write R6250-v1.0.0.62_1.0.62.chk firmware

( executed in ***dd-wrt ) if the current system is DD Execution

Mtd-r Write R6250-v1.0.0.62_1.0.62.chk Linux

After this step is executed, R6259 is half a brick, don't worry, just do the following 6 ~ 8 step back to the factory state immediately .

--------------------------------------------------------------------------------

The following steps are all on your own computer Win7 System of cmd under execution,

6. Set the computer IP address to:192.168.1.150 This should have been set up beforehand.

7. start running cmd to open a window to execute. The main is to judge the progress of the brush home.  

Ping 192.168.1.1-t

8. start running cmd and open a window to execute. CD into the directory where you downloaded the firmware and execute the command below.  

Tftp-i 192.168.1.1 put R6250-v1.0.0.62_1.0.62.chk

Transfer success: A seconds 10829882 bytes, 902490 bytes / seconds  

A similar hint above indicates success. (after the upgrade is completed , Ping the 192.168.1.1 route will occasionally have a large delay, is normal, upgrade to the latest firmware package, it is normal)

9. with ie enter http:/ /192.168.1.1 , familiar netfear   first restore the initial setup and then upgrade the firmware r6250-v1.0.0.62_1.0.62.chk->r6250-v1.0.0.72_1.0.71.chk, R6250-v1.0.1.80_1.0.75.chk->

R6250-v1.0.1.84_1.0.78.chk-> R6250-v1.0.3.6_10.1.3.chk, R6250-v1.0.4.2_10.1.10.chk->R6250-V1.0.4.6_ 10.1.12.chk-R6250-v1.0.4.8_10.1.13.chk

to this r6250 it's completely restored. WiFi Perfect Signal stable.

Netgear R6250 routing from OpenWrt or DD-WRT system to default system for small white