The method of burning Arduino bootloader with usbasp download line of domestic free drive

Source: Internet
Author: User

This article applies only if the bootloader is damaged and the purchase of a home-made usbasp download line causes the IDE to be unable to recognize and not burn the write. is a slightly non-mainstream mode of operation.

Because the Arduino IDE does not support this free-drive usbasp line, it will prompt for errors.

The whole thing is like this:

1. Symptoms

With the Arduino control servo inadvertently play off, plugged into the computer, in the "Device Manager" does not have a serial prompt, with the Arduino IDE can not download the program to the board, prompted to find the COM port. And the computer can not find the serial port. It is estimated that bootloader is damaged and ready to be re-burned with the usbasp download line.

2. Prepare to resolve

Before the standard usbasp download line sent to cousin, had to buy another. Bought a "domestic-free Drive" Download line, it is the installation of the driver. After plugging into the computer, the serial number is not generated and is only recognized for a usb-hid device.

The normal usbasp line has 10 pins, and Arduino has only 6. But as long as the pin is connected, it can be adapted. Connect the following pins with the DuPont line 22: Mosi,vcc,rst,sck,miso,gnd.

Unfortunately, due to the Arduino IDE's "high-end Air international", it does not recognize this modified firmware of the "Chinese characteristics" usbasp download line, the conventional method can not be burned at all, display the error "could not find USB device" usbasp "" "Avrdude:stk500_getsync (): Not in sync:resp=0x00", unable to connect.

3. Dispel

In the final analysis, Arduino is not a Atmega 328P microcontroller and peripheral circuit, bootloader is also a single-chip flash file, why rely on the Arduino IDE! (that is to say, it was a bit scary when I couldn't write ...) Calm down, calm down. Since there is a download line, we will follow the single-chip play, directly download the compiled Flash files. But which is the Arduino uno flash? What if I don't have a supported downloader in the official list?

This kind of domestic free-drive download line, you can use progisp this software. (AVR fighter seems to work, but the number of supported chip types does not seem to be progisp much)

The download software is selected, but how to set up a bunch of parameters in the software? There is already a description in the Arduino folder. In my case, the "E:\arduino-1.0.5-r2\hardware\arduino" folder in the Boards.txt contains the various models of the Arduino parameters, my is Arduino UNO, the corresponding record parameters in the file are as follows:

##############################################################

Uno.name=arduino Uno

Uno.upload.protocol=arduino

uno.upload.maximum_size=32256

uno.upload.speed=115200

Uno.bootloader.low_fuses=0xff

Uno.bootloader.high_fuses=0xde

uno.bootloader.extended_fuses=0x05

Uno.bootloader.path=optiboot

Uno.bootloader.file=optiboot_atmega328.hex

uno.bootloader.unlock_bits=0x3f

uno.bootloader.lock_bits=0x0f

uno.build.mcu=atmega328p

uno.build.f_cpu=16000000l

Uno.build.core=arduino

Uno.build.variant=standard

##############################################################

This is not exactly remembered, setting a few key values:

1. Connect the following pins with the DuPont line 22: Mosi,vcc,rst,sck,miso,gnd.

Download line into the computer, open the Progisp software, Flash file Select "E:\arduino-1.0.5-r2\hardware\arduino\bootloaders\optiboot" folder "Optiboot_ Atmega328.hex ".

2. The above list of low_fuses=0xff (low fuse bit), high_fuses=0xde (high fuse bit), extended_fuses=0x05 (expansion fuse bit) These three should be set in the Progisp.

3. Click the Software "Automatic", that is, start the automatic erase, reset, burn write, set the fuse bit and so on a series of operations. More than 10 seconds after the prompt is complete.

Then unplug the download line, connect the USB cable to the computer and the Arduino, is it possible to recognize the new hardware and happily write the program?

The method of burning Arduino bootloader with usbasp download line of domestic free drive

Related Article

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.