how to use traceroute

--sendwait=sendwait Minimal time interval be Tween probes (default 0). If the value is more than ten, then it specifies a number in milliseconds, else it's a number of seconds (float point values allowed too)-e--extensions Show ICMP extension S (if present), including Mpls-a--as-path-lookups Perform as path lookups in routing registries and Print results directly after the corresponding addresses-m name--module=name U Se specified module

Application of ICMP--tracerouteTraceroute is an important tool to detect the routing between host and destination hosts, and is also the most convenient tool. As mentioned earlier, although the Ping tool can also detect, however, because of the IP header limit, ping can not be fully recorded under the router. So the traceroute just fills this flaw.The principle of traceroute is very very interesting, it rec

1. traceroute can be used to query routes from one host to another. 2. Principles PingProgramA record routing option is provided, but not all hosts support this option, and the IP header option field can only store up to nine IP addresses. Therefore, it is necessary to develop traceroute.Traceroute uses the TTL fields of the ICMP message and IP header. TTL is an 8-bit field, which is the router's hop counter and also indicates the datagram lifecyc

/bashif ["$#"-ne 1];then echo "Usage-/ping.sh [interface]" echo "excample-./ping.sh 192.168.1.0" echo "Example would perform an ARP scan of the The local subnet to which eth0 are assigned" exitfiprefix=$ (echo $ | cut-d '. '-f 1-3) for addr in $ (SEQ 1 254);d o ping-c 1 $prefix. $addr | grep "bytes from" | cut-d ""-F 4 | Cut-d ":"-F 1done 2. Traceroute route Tracking Not only can we find out if the target m

Ping programThe ping program was written by Mike Muuss to test whether another host is available.The program sends an ICMP echo request message to the main clause and waits for an ICMP echo reply to be returned.The ping program can also detect the return time of this hostTraceroute ProgramThe Traceroute program is a handy tool to explore the TCP/IP protocol in more depthThe Traceroute program allows us to s

=name use specified module (either builtin or external)For traceroute operations. Most methods hasTheir shortcuts ('-I ' means '-m ICMP ' etc.)-O OPTS,...--options=opts,...Use module-specific option OPTS for theTraceroute module. Several OPTS Allowed,separated by comma. If OPTS is ' help ', print infoAbout available options--sport=num

traceroute the principle of:1.traceroute host to be Trace Host Send UDP The destination port is a port with a large number (for example, 33434 Port)2. First package ttl= 1 Span style= "Font-family:simsun;" lang= "ZH-CN" xml:lang= "ZH-CN", dport=33434 ; future packet ttl 1 3. How to determine that you have reached your destination,general destinations are not UDP 33434 this large port to open wha

tcp-m tcp--dport 22-j DROP-A output-m conntrack--ctstate new-j ACCEPTCOMMIT# completed on Fri Dec 19 17:01:18 2014It has been noted that:-A input-j DROP--------------------------------------->ping is output;traceroute when each routing node returns the packet;The rule-a output-m conntrack--ctstate new-j Accept is the TCP protocol by default, whereas the Ping/traceroute uses the ICMP protocol;-A input-p tcp

Command name: PingFunction: Test network connectivityCommand path:/bin/pingUsage: ping [-c] IP addressParameters:-C specify number of times to sendCommand name: ifconfigFunction: View and set network card information (temporary settings)Command path:/sbin/ifconfigUsage: ifconfig [NIC name] [IP Address]Example:Ifconfig eth0 192.168.1.1Command name: tracerouteFunction: Displays the path between the packet and the target host and the time consumed by each nodeCommand path:/bin/tracerouteUsage:

(IP(dst=,ttl=)/TCP(dport=(,),flags=*.*^ packets, got answers, remaining Iii. TCP traceroute Traceroute: used to track the path from the starting point to the destination. With Traceroute, we can know the path of information from your computer to the host on the other end of the Internet. Of course, the path for each packet to arrive at the same destination from

the original IP header and data portion that caused the ICMP error message to be generated (such as UDP or TCP for the transport layer, which contains the port number). Here the original IP header of the Protocol field and the first 8 bytes of the port number, you can determine which protocol and which user process.In addition to the ICMP error message above, the ICMP error message is no longer generated, the general purpose address is the broadcast datagram will no longer produce ICMP error me

The Traceroute tool is used to track the transmission path of datagrams: When a datagram travels from one computer to another, it passes through multiple gateways, and the traceroute command can find all the routers on the datagram transmission path. The transmission path traced through the Traceroute tool is just one of the many pathways between the two computer

Objective: To learn the usage of Linux command Ping,tracerouteUsage of 1:ping:Mans PingPing: Determine if a host is respondinglinux-8o9i:~ #Ping-C4 119.29.29.29PING119.29.29.29(119.29.29.29) About( -) bytes of data. -Bytes from119.29.29.29: icmp_seq=1Ttl=Wuyi Time=101Ms -Bytes from119.29.29.29: icmp_seq=2Ttl=Wuyi Time=75.0Ms -Bytes from119.29.29.29: icmp_seq=3Ttl=Wuyi Time=74.4Ms -Bytes from119.29.29.29: icmp_seq=4Ttl=Wuyi Time=74.2Ms---119.29.29.29 PingStatistics---4Packets Transmitted,4Rec