rj45 loopback

control and monitor the work of Phy. On the basis of MII, I later had the following: Rmii (reduced media independant Interface) Simplifies MII, with fewer signal lines than MII. Gmii (Gigabit media independent interface) Rgmii (reduced Gigabit media independent interface) Connection between PHY and RJ45 There are a large number of simulator devices on the phy, and Mac is a full digital device. The current IC technology can already integrate th

Automatic scanning read/write distance 4 W transmitting antenna unidirectional ≥ 1.3 m, omnidirectional ≥ 0.9m antenna connector 50Ω SMA Communication Interface RS/232, VGA, DI power warning light, DC12V; Control System and LCD, DC24V, 1A warning light source over-Bright Light Emitting Diode Communication Interface RS232, VGA, USB, RJ45, DI, DO power supply 220 V, AC single board control module operating system Windows, Dos transmit power ~ 10 W 1 dB

centers is more distinctive. Flexibility In a data center, the device can be configured with both the optical network card and the copper network card, and the number of two ports for different devices and specific applications does not have a definite value, this requires that the cabling product be flexibly configured according to specific requirements. Hybrid-Patch adopts a modular structure and can be divided into different modules, each module can be installed with a number of modules as n

). Bidirectional detachable copper cable distribution frame Speaking of RJ45 interface copper distribution frames, there is still a history. At the end of 1980s, when integrated wiring entered China, the transmission rate was very low and there were only three types of cables. Therefore, the wiring system had only 110 distribution frames, either a horizontal subsystem or a main subsystem, all use this system, mainly used together with the large log

-232, RS-422 and RS-485 standards only to interface electrical characteristics to make provisions, and does not involve connectors, cables or protocols, on this basis, users can establish their own high-level communication protocols. The most frequently used plug-ins we encounter in our actual work have three DB9 DB25 RJ45 plug-ins. The above three plug-ins can be used as serial port plug-ins, you can also switch between sockets through cables. Next w

1000base-x location. 2. MDI interfaceMDI is the interface between the PHY chip and the physical medium, the RJ45 interface is common. Hundred gigabit Nets, MDI four lines, two pairs of differential signals, only with the RJ45 1,2,3,6 line,. Gigabit Network, MDI altogether 8 lines, four pairs of differential signals, with the RJ45 8 lines again

I have seen a lot of articles to make Raspberry Pi into a wireless AP, but what I want to do today is to make Raspberry Pi into a NAT-enabled router, I did this because I was on a business trip to Holland and found my bambook unable to access the dorm WiFi, Perhaps because the dorm wireless router is the way to authenticate WEP, in short, not even. Later decided to use Raspberry pi+ Arctic Starlight Wireless router to solve the problem. Ideas:"Wireless Router"-----"wireless network card--raspber

Millet Notebook air can be directly plugged into the Internet network ? First look at the two-sided Millet notebook air interface, you can see only 2 USB 3.0 interface, 1 HDMI high-definition video interface, 1 standard headphone/mac interface, no other interface for the first time, as shown in the picture. Millet notebook Air Expansion interface diagram As can be seen from the above, the Millet notebook Air expansion interface is relatively small, not equipped with

Experimental topologySoftware version GN3 0.8.6 ASA image 8.0 (2)650) this.width=650; "src=" Http://s3.51cto.com/wyfs02/M02/76/D9/wKioL1ZdmSGAvspoAABLsjqDXwk949.png "title=" 9qzzvef@]278 ' U@5uoyg) 0m.png "alt=" Wkiol1zdmsgavspoaablsjqdxwk949.png "/>Experimental environmentR1 and R2 Simulation company intranet, R3 analog Internet equipment. ASA as a company export, implementing NAT address translationExperimental requirementsDoing dynamic NAT on the ASA to convert the address of the R1

Beaglebone_black login: Root Password: Last login: Fri Dec 31 19:00:20 est 1999 on ttyo0 [Email protected] _ BLACK :~ # [Email protected] _ BLACK :~ # Pwd /Home/root [Email protected] _ BLACK :~ # Ifconfig Eth0 link encap: Ethernet hwaddr C8: A0: 30: B9: 7f: 2b Up broadcast multicast MTU: 1500 Metric: 1 RX packets: 0 errors: 0 dropped: 0 overruns: 0 frame: 0 TX packets: 0 errors: 0 dropped: 0 overruns: 0 carrier: 0 Collisions: 0 FIG: 1000 RX Bytes: 0 (0.0 B) TX Bytes:

Intranet interaction and the other for isp interaction. the actual topology is as follows: the isp line is directly connected to the vswitch, instead of the vro. The vro is also connected to a port of the vswitch. Its function is only for nat, re-encapsulate the original address of the package and the destination address of the returned package (see the original post). If the Intranet host wants to send packets to the Internet host, after these packets are sent to the Ethernet port of the route

255.255.255.255 s2/0 13.1.1.1R3 ip route 2.2.2.2 255.255.255.255 s2/0 13.1.1.1R3 ip route 12.1.1. 0 worker s2/0 worker ping 2.2.2.2 source loopback 0R1 ping 3.3.3.3 source loopback 0R2 ping 1.1.1.1 source loopback 0R2 ping 3.3.3.3 source loopback 0R3 ping 2.2.2.2 source loopback